The Dwight D. Eisenhower National System of Interstate and Defense Highways, commonly known as the Interstate Highway System, is a network of controlled-access highways that forms part of the National Highway System in the United States. The system is named for President Dwight D. Eisenhower, who championed its formation. Construction was authorized by the Federal Aid Highway Act of 1956, and the original portion was completed 35 years later, although some urban routes were cancelled and never built. The network has since been extended and, as of 2016, it has a total length of 48,191 miles (77,556 km). As of 2016, about one-quarter of all vehicle miles driven in the country use the Interstate system. In 2006, the cost of construction was estimated at about $425 billion (equivalent to $499 billion in 2016).
|Dwight D. Eisenhower National System of Interstate and Defense Highways|
Highway shields for Interstate 80, Business Loop Interstate 80, and the Eisenhower Interstate System
Interstate Highways in the 48 contiguous states. Alaska, Hawaii, and Puerto Rico also have Interstate Highways. (See version with numbers.)
|Length||48,191 mi[a] (77,556 km)|
|Formed||June 29, 1956|
|Interstates||Interstate X (I-X)|
The United States government's efforts to construct a national network of highways began on an ad hoc basis with the passage of the Federal Aid Road Act of 1916, which provided for $75 million over a five-year period for matching funds to the states for the construction and improvement of highways. The nation's revenue needs associated with World War I prevented any significant implementation of this policy, which expired in 1921.
In December 1918, E. J. Mehren, a civil engineer and the editor of Engineering News-Record, presented his "A Suggested National Highway Policy and Plan" during a gathering of the State Highway Officials and Highway Industries Association at the Congress Hotel in Chicago. In the plan, Mehren proposed a 50,000-mile (80,000 km) system, consisting of five east–west routes and 10 north–south routes. The system would include two percent of all roads and would pass through every state at a cost of $25,000 per mile ($16,000/km), providing commercial as well as military transport benefits.
As the landmark 1916 law expired, new legislation was passed—the Federal Aid Highway Act of 1921 (Phipps Act). This new road construction initiative once again provided for federal matching funds for road construction and improvement, $75 million allocated annually. Moreover, this new legislation for the first time sought to target these funds to the construction of a national road grid of interconnected "primary highways", setting up cooperation among the various state highway planning boards.
The Bureau of Public Roads asked the Army to provide a list of roads that it considered necessary for national defense. In 1922, General John J. Pershing, former head of the American Expeditionary Force in Europe during the war, complied by submitting a detailed network of 20,000 miles (32,000 km) of interconnected primary highways—the so-called Pershing Map.
A boom in road construction followed throughout the decade of the 1920s, with such projects as the New York parkway system constructed as part of a new national highway system. As automobile traffic increased, planners saw a need for such an interconnected national system to supplement the existing, largely non-freeway, United States Numbered Highways system. By the late 1930s, planning had expanded to a system of new superhighways.
In 1938, President Franklin D. Roosevelt gave Thomas MacDonald, chief at the Bureau of Public Roads, a hand-drawn map of the United States marked with eight superhighway corridors for study. In 1939, Bureau of Public Roads Division of Information chief Herbert S. Fairbank wrote a report called Toll Roads and Free Roads, "the first formal description of what became the interstate highway system" and, in 1944, the similarly themed Interregional Highways.
The Interstate Highway System gained a champion in President Dwight D. Eisenhower, who was influenced by his experiences as a young Army officer crossing the country in the 1919 Army Convoy on the Lincoln Highway, the first road across America. Eisenhower gained an appreciation of the Reichsautobahn system, the first "national" implementation of modern Germany's Autobahn network, as a necessary component of a national defense system while he was serving as Supreme Commander of the Allied forces in Europe during World War II. He recognized that the proposed system would also provide key ground transport routes for military supplies and troop deployments in case of an emergency or foreign invasion.
The publication in 1955 of the General Location of National System of Interstate Highways, informally known as the Yellow Book, mapped out what became the Interstate System. Assisting in the planning was Charles Erwin Wilson, who was still head of General Motors when President Eisenhower selected him as Secretary of Defense in January 1953.
Three states have claimed the title of first Interstate Highway. Missouri claims that the first three contracts under the new program were signed in Missouri on August 2, 1956. The first contract signed was for upgrading a section of US Route 66 to what is now designated Interstate 44. On August 13, 1956, Missouri awarded the first contract based on new Interstate Highway funding; this work began on US 40 (now I-70) in St. Charles County.
Kansas claims that it was the first to start paving after the act was signed. Preliminary construction had taken place before the act was signed, and paving started September 26, 1956. The state marked its portion of I-70 as the first project in the United States completed under the provisions of the new Federal-Aid Highway Act of 1956.
The Pennsylvania Turnpike could also be considered one of the first Interstate Highways. On October 1, 1940, 162 miles (261 km) of the highway now designated I‑70 and I‑76 opened between Irwin and Carlisle. The Commonwealth of Pennsylvania refers to the turnpike as the Granddaddy of the Pikes.
Milestones in the construction of the Interstate Highway System include:
The system was proclaimed complete in 1992, but two of the original interstates—I-95 and I-70—are not continuous: both of these discontinuities are due to local opposition, which has blocked efforts to build the necessary connections to fully complete the system.
I-95 is discontinuous in New Jersey because of the cancellation of the Somerset Freeway. This situation is being remedied; the Pennsylvania Turnpike/Interstate 95 Interchange Project currently under construction will connect the separate sections of I‑95 to form a continuous route, completing the final section of the original plan. Construction began in 2010.
Likewise, I-70 is discontinuous in Pennsylvania, because of the lack of a direct interchange with the Pennsylvania Turnpike at the eastern end of the concurrency near Breezewood. Traveling in either direction, I-70 traffic must exit the freeway and use a short stretch of US 30 (which includes a number of roadside services) to rejoin I-70. The interchange was not originally built because of a legacy federal funding rule, since relaxed, which restricted the use of federal funds to improve roads financed with tolls. Solutions have been proposed to eliminate the discontinuity, but they have been blocked by local opposition, fearing a loss of business.
The Interstate Highway system has been expanded numerous times. The expansions have both created new designations and extended existing designations. For example, I-49, added to the system in the 1980s as a freeway in Louisiana, was designated as an expansion corridor, and FHWA approved the expanded route north from Lafayette, to Kansas City, Missouri. The freeway exists today as separate completed segments, with segments under construction or in the planning phase between them.
In 1966, the FHWA designated the entire Interstate Highway System as part of the larger Pan-American Highway System, and at least two proposed Interstate expansions were initiated to help trade with Canada and Mexico spurred by the North American Free Trade Agreement (NAFTA). Long-term plans for I-69, which currently exists in several separate completed segments (the largest of which are in Indiana and Texas), is to have the highway route extend from Tamaulipas, Mexico to Ontario, Canada. The planned I-11 will then bridge the Interstate gap between Phoenix, Arizona and Las Vegas, Nevada, and thus form part of the CANAMEX Corridor (along with I-19, and portions of I-10 and I-15) between Sonora, Mexico and Alberta, Canada.
Political opposition from residents canceled many freeway projects around the United States, including:
The American Association of State Highway and Transportation Officials (AASHTO) has defined a set of standards that all new Interstates must meet unless a waiver from the Federal Highway Administration (FHWA) is obtained. One almost absolute standard is the controlled access nature of the roads. With few exceptions, traffic lights (and cross traffic in general) are limited to toll booths and ramp meters (metered flow control for lane merging during rush hour).
Being freeways, Interstate Highways usually have the highest speed limits in a given area. Speed limits are determined by individual states. From 1974 to 1986, the maximum speed limit on any highway in the United States was 55 miles per hour (90 km/h), in accordance with federal law.
Typically, lower limits are established in Northeastern and coastal states, while higher speed limits are established in inland states west of the Mississippi River. For example, the maximum speed limit is 75 mph (120 km/h) in northern Maine, varies between 50 and 70 mph (80 and 115 km/h) from southern Maine to New Jersey, and is 50 mph (80 km/h) in New York City and the District of Columbia. Currently, rural speed limits elsewhere generally range from 65 to 80 miles per hour (105 to 130 km/h). Several portions of various highways such as I-10 and I-20 in rural western Texas, I-80 in Nevada between Fernley and Winnemuca (except around Lovelock) and portions of I-15, I-70, I-80, and I-84 in Utah have a speed limit of 80 mph (130 km/h). Other interstate highways in Idaho, Montana, South Dakota and Wyoming also have the same high speed limits.
In some areas, speed limits on Interstates can be significantly lower in areas where they traverse significantly hazardous areas. The maximum speed limit on I-90 is 50 mph (80 km/h) in downtown Cleveland because of two sharp curves with a suggested limit of 35 mph (55 km/h) in a heavily congested area; I-70 through Wheeling, West Virginia, has a maximum speed limit of 45 mph (70 km/h) through the Wheeling Tunnel and most of downtown Wheeling; and I-68 has a maximum speed limit of 40 mph (65 km/h) through Cumberland, Maryland, because of multiple hazards including sharp curves and narrow lanes through the city. In some locations, low speed limits are the result of lawsuits and resident demands; after holding up the completion of I-35E in St. Paul, Minnesota, for nearly 30 years in the courts, residents along the stretch of the freeway from the southern city limit to downtown successfully lobbied for a 45 mph (70 km/h) speed limit in addition to a prohibition on any vehicle weighing more than 9,000 pounds (4,100 kg) gross vehicle weight. I-93 in Franconia Notch State Park in northern New Hampshire has a speed limit of 45 mph (70 km/h) because it is a parkway that consists of only one lane per side of the highway. On the other hand, Interstates 15, 80 and 84 in Utah have speed limits as high as 70 mph (115 km/h) within the Salt Lake City, Cedar City, and St. George areas, and I-25 in New Mexico within the Santa Fe and Las Vegas areas along with I-20 in Texas along Odessa and Midland and I-29 in North Dakota along the Grand Forks area have higher speed limits of 75 mph (120 km/h).
As one of the components of the National Highway System, Interstate Highways improve the mobility of military troops to and from airports, seaports, rail terminals, and other military bases. Interstate Highways also connect to other roads that are a part of the Strategic Highway Network, a system of roads identified as critical to the U.S. Department of Defense.
The system has also been used to facilitate evacuations in the face of hurricanes and other natural disasters. An option for maximizing traffic throughput on a highway is to reverse the flow of traffic on one side of a divider so that all lanes become outbound lanes. This procedure, known as contraflow lane reversal, has been employed several times for hurricane evacuations. After public outcry regarding the inefficiency of evacuating from southern Louisiana prior to Hurricane Georges' landfall in September 1998, government officials looked towards contraflow to improve evacuation times. In Savannah, Georgia, and Charleston, South Carolina, in 1999, lanes of I-16 and I-26 were used in a contraflow configuration in anticipation of Hurricane Floyd with mixed results.
In 2004 contraflow was employed ahead of Hurricane Charley in the Tampa, Florida area and on the Gulf Coast before the landfall of Hurricane Ivan; however, evacuation times there were no better than previous evacuation operations. Engineers began to apply lessons learned from the analysis of prior contraflow operations, including limiting exits, removing troopers (to keep traffic flowing instead of having drivers stop for directions), and improving the dissemination of public information. As a result, the 2005 evacuation of New Orleans, Louisiana, prior to Hurricane Katrina ran much more smoothly.
A widespread urban legend states that one out of every five miles of the Interstate Highway System must be built straight and flat so as to be usable by aircraft during times of war. Contrary to popular lore, Interstate Highways are not designed to serve as airstrips.
The numbering scheme for the Interstate Highway System was developed in 1957 by the American Association of State Highway and Transportation Officials (AASHTO). The association's present numbering policy dates back to August 10, 1973. Within the continental United States, primary Interstates—also called main line Interstates or two-digit Interstates—are assigned numbers less than 100.
In the numbering scheme for the primary routes, east–west highways are assigned even numbers and north–south highways are assigned odd numbers. Odd route numbers increase from west to east, and even-numbered routes increase from south to north (to avoid confusion with the U.S. Highways, which increase from east to west and north to south), though there are exceptions to both principles in several locations. This numbering system usually holds true even if the local direction of the route does not match the compass directions. For example, I-94 between Chicago and Milwaukee runs primarily north–south, but bears an east–west designation to match its overall orientation, with the "east" label matching the local southward routing, and so on. In some cases the deviation can be drastic; for example, I-64 runs almost exactly the wrong way in the Hampton Roads region, where sections that once were labeled "east" that run almost due west have had these labels removed due to confusion in the Norfolk, Virginia, area. While in many cases, this is due to relatively short deviations, compared to the overall routing of the highway, it is not always the case. For example, I-26 is labeled east–west as its number suggests, but it carries a more generally north–south routing. Some states, such as Michigan in the case of I-69, have chosen to violate the numbering conventions by signing the route to match its local orientation rather than the normal convention. Numbers divisible by five are intended to be major arteries among the primary routes, carrying traffic long distances. Major north–south arterial Interstates increase in number from I-5 between Canada and Mexico along the West Coast to I‑95 between Canada and Miami, Florida along the East Coast; the exception is I-45, which does not leave the state of Texas, running from Galveston to Dallas. Major west–east arterial Interstates increase in number from I-10 between Santa Monica, California, and Jacksonville, Florida, to I-90 between Seattle, Washington, and Boston, Massachusetts, with two exceptions. The exception is I-30, which is shorter than the other major east–west interstates, running from Fort Worth, Texas to Little Rock, Arkansas. There are no I-50 and I-60, as routes with those numbers would likely pass through states that currently have U.S. Highways with the same numbers, which is generally disallowed under highway administration guidelines.
Several two-digit numbers are shared between road segments at opposite ends of the country for various reasons. Some such highways are incomplete Interstates (such as I-69 and I-74) and some just happen to share route designations (such as I-76, I-84, I‑86, I-87, and I-88). Some of these were due to a change in the numbering system as a result of a new policy adopted in 1973. Previously, letter-suffixed numbers were used for long spurs off primary routes; for example, western I‑84 was I‑80N, as it went north from I‑80. The new policy stated, "No new divided numbers (such as I-35W and I-35E, etc.) shall be adopted." The new policy also recommended that existing divided numbers be eliminated as quickly as possible; however, an I-35W and I-35E still exist in the Dallas–Fort Worth metroplex in Texas, and an I-35W and I-35E that run through Minneapolis and Saint Paul, Minnesota, still exist. Additionally, due to Congressional requirements, three sections of I-69 in southern Texas will be divided into I-69W, I-69E, and I-69C (for Central).
AASHTO policy allows dual numbering to provide continuity between major control points. This is referred to as a concurrency or overlap. For example, I‑75 and I‑85 share the same roadway in Atlanta; this 7.4-mile (11.9 km) section, called the Downtown Connector, is labeled both I‑75 and I‑85. Concurrencies between Interstate and U.S. Route numbers are also allowed in accordance with AASHTO policy, as long as the length of the concurrency is reasonable. In rare instances, two highway designations sharing the same roadway are signed as traveling in opposite directions; one such wrong-way concurrency is found between Wytheville and Fort Chiswell, Virginia, where I‑81 north and I‑77 south are equivalent (with that section of road traveling almost due east), as are I‑81 south and I‑77 north.
Auxiliary Interstate Highways are circumferential, radial, or spur highways that principally serve urban areas. These types of Interstate Highways are given three-digit route numbers, which consist of a single digit prefixed to the two-digit number of its parent Interstate Highway. Spur routes deviate from their parent and do not return; these are given an odd first digit. Circumferential and radial loop routes return to the parent, and are given an even first digit. Unlike primary Interstates, three-digit Interstates are signed as either east–west or north–south, depending on the general orientation of the route, without regard to the route number. For instance, I-190 in Massachusetts is labeled north–south, while I-195 in New Jersey is labeled east–west. Some looped Interstate routes use inner–outer directions instead of compass directions, when the use of compass directions would create ambiguity. Due to the large number of these routes, auxiliary route numbers may be repeated in different states along the mainline. Some auxiliary highways do not follow these guidelines, however.
The Interstate Highway System also extends to Alaska, Hawaii, and Puerto Rico, even though they have no direct land connections to any other states or territories. However, their residents still pay federal fuel and tire taxes.
The Interstates in Hawaii, all located on the most populous island of Oahu, carry the prefix H. There are three one-digit routes in the state (H-1, H-2, and H-3) and one auxiliary route (H-201). These Interstates connect several military and naval bases together, as well as the important cities and towns spread across Oahu, and especially the metropolis of Honolulu.
Both Alaska and Puerto Rico also have public highways that receive 90 percent of their funding from the Interstate Highway program. The Interstates of Alaska and Puerto Rico are numbered sequentially in order of funding without regard to the rules on odd and even numbers. They also carry the prefixes A and PR, respectively. However, these highways are signed according to their local designations, not their Interstate Highway numbers. Furthermore, these routes were neither planned according to nor constructed to the official Interstate Highway standards.
On one- or two-digit Interstates, the mile marker numbering almost always begins at the southern or western state line. If an Interstate originates within a state, the numbering begins from the location where the road begins in the south or west. Exceptions exist for Interstate Highways that used segments of roadway that were built prior to Interstate Highway standards being formalized and were grandfathered into the system.
Three-digit Interstates with an even first number that form a complete circumferential (circle) bypass around a city feature mile markers that are numbered in a clockwise direction, beginning just west of an Interstate that bisects the circumferential route near a south polar location. In other words, mile marker 1 on I-465, a 53-mile (85 km) route around Indianapolis, is just west of its junction with I-65 on the south side of Indianapolis (on the south leg of I-465), and mile marker 53 is just east of this same junction. An exception is I-495 in the Washington, DC Metropolitan Area, with mileposts increasing counterclockwise because part of that road is also part of I-95.
The exit numbers of interchanges are either sequential or distance-based so that the exit number is the same as the nearest mile marker. Under the latter system, a single mile with multiple exits may be assigned letter suffixes, for example on I‑890 in New York.
Markers for Business Loop Interstate 80 (left) and Business Spur Interstate 80 (right)
AASHTO defines a category of special routes separate from primary and auxiliary Interstate designations. These routes do not have to comply to Interstate construction standards but are routes that may be identified and approved by the association. The same route marking policy applies to both US Numbered Highways and Interstate Highways; however, business route designations are sometimes used for Interstate Highways. Known as Business Loops and Business Spurs, these routes principally travel through the corporate limits of a city, passing through the central business district when the regular route is directed around the city. They also use a green shield instead of the red and blue shield.
Interstate highways and their rights of way are owned by the state in which they were built. The last federally owned portion of the Interstate System was the Woodrow Wilson Bridge on the Washington DC Capital Beltway. The new bridge was completed in 2009 and is collectively owned by Virginia and Maryland. Maintenance is generally the responsibility of the state department of transportation. However, there are some segments of Interstate owned and maintained by local authorities.
About 70 percent of the construction and maintenance costs of Interstate Highways in the United States have been paid through user fees, primarily the fuel taxes collected by the federal, state, and local governments. To a much lesser extent they have been paid for by tolls collected on toll highways and bridges. The Highway Trust Fund, established by the Highway Revenue Act in 1956, prescribed a three-cent-per-gallon fuel tax, soon increased to 4.5 cents per gallon. Since 1993 the tax has remained at 18.4 cents per gallon.
The rest of the costs of these highways are borne by general fund receipts, bond issues, designated property taxes, and other taxes. The federal contribution comes overwhelmingly from motor vehicle and fuel taxes (93.5 percent in 2007), as does about 60 percent of the state contribution. However, any local government contributions are overwhelmingly from sources besides user fees. The portion of the user fees spent on highways themselves covers about 57 percent of their costs, with about one-sixth of the user fees being sent to other programs, including the mass transit systems in large cities. Some large sections of Interstate Highways that were planned or constructed before 1956 are still operated as toll roads. Others have had their construction bonds paid off and they have become toll-free, such as in Connecticut (I‑95), Maryland (I‑95), Virginia (I‑95), and Kentucky (I‑65).
As American suburbs have expanded, the costs incurred in maintaining freeway infrastructure have also grown, leaving little in the way of funds for new Interstate construction. This has led to the proliferation of toll roads (turnpikes) as the new method of building limited-access highways in suburban areas. Some Interstates are privately maintained (for example, the VMS company maintains I‑35 in Texas) to meet rising costs of maintenance and allow state departments of transportation to focus on serving the fastest-growing regions in their states.
Parts of the Interstate System might have to be tolled in the future to meet maintenance and expansion demands, as has been done with adding toll HOV/HOT lanes in cities such as Atlanta, Dallas, and Los Angeles. Although part of the tolling is an effect of the SAFETEA‑LU act, which has put an emphasis on toll roads as a means to reduce congestion, present federal law does not allow for a state to change a freeway section to a tolled section for all traffic.
Approximately 2,900 miles (4,700 km) of toll roads are included in the Interstate Highway System. While federal legislation initially banned the collection of tolls on Interstates, many of the toll roads on the system were either completed or under construction when the Interstate Highway System was established. Since these highways provided logical connections to other parts of the system, they were designated as Interstate highways. Congress also decided that it was too costly to either build toll-free Interstates parallel to these toll roads, or directly repay all the bondholders who financed these facilities and remove the tolls. Thus, these toll roads were grandfathered into the Interstate Highway System.
Toll facilities designated as Interstate highways (such as the Massachusetts Turnpike) were typically allowed to continue collecting tolls, but are generally ineligible to receive federal funds for maintenance and improvements. Some toll roads that did receive federal funds to finance emergency repairs (notably the Connecticut Turnpike (I-95) following the Mianus River Bridge collapse) were required to remove tolls as soon as the highway's construction bonds were paid off. In addition, these toll facilities were grandfathered from Interstate Highway standards. A notable example is the western approach to the Benjamin Franklin Bridge in Philadelphia, where I-676 has a surface street section through a historic area.
Policies on toll facilities and Interstate Highways have since changed. The Federal Highway Administration has allowed some states to collect tolls on existing Interstate Highways, while a recent extension of I-376 included a section of Pennsylvania Route 60 that was tolled by the Pennsylvania Turnpike Commission before receiving Interstate designation. Also, newer toll facilities (like the tolled section of I-376, which was built in the early 1990s) must conform to Interstate standards. A new addition of the Manual on Uniform Traffic Control Devices in 2009 requires a black-on-yellow "Toll" sign to be placed above the Interstate trailblazer on Interstate Highways that collect tolls.
Legislation passed in 2005 known as SAFETEA-LU, encouraged states to construct new Interstate Highways through "innovative financing" methods. SAFETEA-LU facilitated states to pursue innovative financing by easing the restrictions on building interstates as toll roads, either through state agencies or through public–private partnerships. However, SAFETEA-LU left in place a prohibition of installing tolls on existing toll-free Interstates, and states wishing to toll such routes to finance upgrades and repairs must first seek approval from Congress.
Interstate Highways financed with federal funds are known as "chargeable" Interstate routes, and are considered part of the 42,000-mile (68,000 km) network of highways. Federal laws also allow "non-chargeable" Interstate routes, highways funded similarly to state and U.S. Highways to be signed as Interstates, if they both meet the Interstate Highway standards and are logical additions or connections to the system. These additions fall under two categories: routes that already meet Interstate standards, and routes not yet upgraded to Interstate standards. Only routes that meet Interstate standards may be signed as Interstates once their proposed number is approved.
Interstate Highways are signed by a number placed on a trademarked red, white, and blue sign. The colors red, white, and blue are chosen because they are the colors of the American flag. In the original design, the name of the state was displayed above the highway number, but in many states, this area is now left blank, allowing for the printing of larger and more-legible digits. The sign usually measures 36 inches (91 cm) high, and is 36 inches (91 cm) wide for two-digit Interstates or 45 inches (110 cm) for three-digit Interstates.
Interstate business loops and spurs use a special shield in which the red and blue are replaced with green, the word "BUSINESS" appears instead of "INTERSTATE", and the word "SPUR" or "LOOP" usually appears above the number. The green shield is employed to mark the main route through a city's central business district, which intersects the associated Interstate highway at one (spur) or both (loop) ends of the business route. The route usually traverses the main thoroughfare(s) of the city's downtown area or other major business district. A city may have more than one Interstate-derived business route, depending on the number of Interstates passing through a city and the number of significant business districts therein.
Over time, the design of the Interstate shield has changed. In 1957 the Interstate shield designed by Texas Highway Department employee Richard Oliver was introduced, the winner of a contest that included 100 entries; at the time, the shield color was a dark navy blue and only 17 inches (43 cm) wide. The Manual on Uniform Traffic Control Devices (MUTCD) standards revised the shield in the 1961, 1971, and 1978 editions.
The majority of Interstates have exit numbers. All traffic signs and lane markings on the Interstates are supposed to be designed in compliance with the Manual on Uniform Traffic Control Devices (MUTCD). There are, however, many local and regional variations in signage.
For many years, California was the only state that did not use an exit numbering system. It was granted an exemption in the 1950s due to having an already largely completed and signed highway system; placing exit number signage across the state was deemed too expensive. To control costs, California began to incorporate exit numbers on its freeways in 2002—Interstate, U.S., and state routes alike. Caltrans commonly installs exit number signage only when a freeway or interchange is built, reconstructed, retrofitted, or repaired, and it is usually just tacked onto the top-right corner of an already existing sign. Newer signs along the freeways follow this practice as well. Most exits along California's Interstates now have exit number signage, particularly in rural areas. California, however, still does not use mileposts, although a few exist for experiments or for special purposes.
Exit numbers correspond to Interstate mileage markers in most states. On I‑19 in Arizona, however, length is measured in kilometers instead of miles because, at the time of construction, a push for the United States to change to a metric system of measurement had gained enough traction that it was mistakenly assumed that all highway measurements would eventually be changed to metric; proximity to metric-using Mexico may also have been a factor, as I‑19 indirectly connects I‑10 to the Mexican Federal Highway system via surface streets in Nogales. Mileage count increases from west to east on most even-numbered Interstates; on odd-numbered Interstates mileage count increases from south to north. Some highways, including the New York State Thruway, use sequential exit-numbering schemes. Exits on the New York State Thruway count up from Yonkers traveling north, and then west from Albany.
As of November 2010, the Illinois State Tollway Authority has redone the mileage markers to be uniform with the rest of the state on I‑90 (Jane Addams Memorial/Northwest Tollway) and the I‑94 section of the Tri‑State Tollway, which previously had matched the I‑294 section starting in the south at I‑80/I‑94/IL Route 394. The tollway is also currently in the process of adding exit number tabs to the exits.
Many northeastern states label exit numbers sequentially, regardless of how many miles have passed between exits. States in which Interstate exits are still numbered sequentially are Connecticut, Delaware, Massachusetts, New Hampshire, New York, Rhode Island, and Vermont; as such, five of the main Interstate highways that remain completely within these states (87, 88, 89, 91, and 93) have interchanges numbered sequentially along their entire routes. Maine, Pennsylvania, Virginia, Georgia, and Florida followed this system for a number of years, but since converted to mileage-based exit numbers. Georgia renumbered in 2000, while Maine did so in 2004. The Pennsylvania Turnpike uses both mile marker numbers and sequential numbers. Mile marker numbers are used for signage, while sequential numbers are used for numbering interchanges internally. The New Jersey Turnpike, including the portions that are signed as I‑95 and I‑78, also has sequential numbering, but other Interstates within New Jersey use mile markers.
I‑87 in New York State is numbered in three sections. The first section makes up the Major Deegan Expressway in the Bronx, with interchanges numbered sequentially from 1 to 14. The second section of I‑87 is a part of the New York State Thruway that starts in Yonkers (exit 1) and continues north to Albany (exit 24); at Albany, the Thruway turns west and becomes I‑90 for exits 25 to 61. From Albany north to the Canadian border, the exits on I‑87 are numbered sequentially from 1 to 44 along the Adirondack Northway. This often leads to confusion as there is more than one exit on I‑87 with the same number. For example, exit 4 on Thruway section of I‑87 connects with the Cross County Parkway in Yonkers, but exit 4 on the Northway is the exit for the Albany airport. These two exits share a number but are located 150 miles (240 km) apart.
There are four common signage methods on Interstates:
Proposed I-41 in Wisconsin and partly completed I-74 in North Carolina respectively are possible and current exceptions not adhering to the guideline. It is not known if the U.S. Highways with the same numbers will be retained in the states upon completion of the Interstate routes.