IEEE 802.11 is part of the IEEE 802 set of LAN protocols, and specifies the set of media access control (MAC) and physical layer (PHY) protocols for implementing wireless local area network (WLAN) Wi-Fi computer communication in various frequencies, including but not limited to 2.4, 5, and 60 GHz frequency bands.
They are the world's most widely used wireless computer networking standards, used in most home and office networks to allow laptops, printers, and smartphones to talk to each other and access the Internet without connecting wires. They are created and maintained by the Institute of Electrical and Electronics Engineers (IEEE) LAN/MAN Standards Committee (IEEE 802). The base version of the standard was released in 1997, and has had subsequent amendments. The standard and amendments provide the basis for wireless network products using the Wi-Fi brand. While each amendment is officially revoked when it is incorporated in the latest version of the standard, the corporate world tends to market to the revisions because they concisely denote capabilities of their products. As a result, in the marketplace, each revision tends to become its own standard.
Although IEEE 802.11 specifications list channels that might be used, the radio frequency spectrum availability allowed varies significantly by regulatory domain.
The 802.11 family consists of a series of half-duplex over-the-air modulation techniques that use the same basic protocol. The 802.11 protocol family employ carrier-sense multiple access with collision avoidance whereby equipment listens to a channel for other users (including non 802.11 users) before transmitting each packet.
802.11-1997 was the first wireless networking standard in the family, but 802.11b was the first widely accepted one, followed by 802.11a, 802.11g, 802.11n, and 802.11ac. Other standards in the family (c–f, h, j) are service amendments that are used to extend the current scope of the existing standard, which may also include corrections to a previous specification.
802.11b and 802.11g use the 2.4 GHz ISM band, operating in the United States under Part 15 of the U.S. Federal Communications Commission Rules and Regulations; 802.11n can also use that band. Because of this choice of frequency band, 802.11b/g/n equipment may occasionally suffer interference in the 2.4 GHz band from microwave ovens, cordless telephones, and Bluetooth devices etc. 802.11b and 802.11g control their interference and susceptibility to interference by using direct-sequence spread spectrum (DSSS) and orthogonal frequency-division multiplexing (OFDM) signaling methods, respectively.
802.11a uses the 5 GHz U-NII band, which, for much of the world, offers at least 23 non-overlapping 20 MHz-wide channels rather than the 2.4 GHz ISM frequency band offering only three non-overlapping 20 MHz-wide channels, where other adjacent channels overlap—see list of WLAN channels. Better or worse performance with higher or lower frequencies (channels) may be realized, depending on the environment. 802.11n can use either the 2.4 or 5 GHz band; 802.11ac uses only the 5 GHz band.
The segment of the radio frequency spectrum used by 802.11 varies between countries. In the US, 802.11a and 802.11g devices may be operated without a license, as allowed in Part 15 of the FCC Rules and Regulations. Frequencies used by channels one through six of 802.11b and 802.11g fall within the 2.4 GHz amateur radio band. Licensed amateur radio operators may operate 802.11b/g devices under Part 97 of the FCC Rules and Regulations, allowing increased power output but not commercial content or encryption.
In 1991 NCR Corporation/AT&T (now Nokia Labs and LSI Corporation) invented a precursor to 802.11 in Nieuwegein, the Netherlands. The inventors initially intended to use the technology for cashier systems. The first wireless products were brought to the market under the name WaveLAN with raw data rates of 1 Mbit/s and 2 Mbit/s.
The major commercial breakthrough came with Apple Inc. adopting Wi-Fi for their iBook series of laptops in 1999. It was the first mass consumer product to offer Wi-Fi network connectivity, which was then branded by Apple as AirPort. One year later IBM followed with its ThinkPad 1300 series in 2000.
The original version of the standard IEEE 802.11 was released in 1997 and clarified in 1999, but is now obsolete. It specified two net bit rates of 1 or 2 megabits per second (Mbit/s), plus forward error correction code. It specified three alternative physical layer technologies: diffuse infrared operating at 1 Mbit/s; frequency-hopping spread spectrum operating at 1 Mbit/s or 2 Mbit/s; and direct-sequence spread spectrum operating at 1 Mbit/s or 2 Mbit/s. The latter two radio technologies used microwave transmission over the Industrial Scientific Medical frequency band at 2.4 GHz. Some earlier WLAN technologies used lower frequencies, such as the U.S. 900 MHz ISM band.
Legacy 802.11 with direct-sequence spread spectrum was rapidly supplanted and popularized by 802.11b.
802.11a, published in 1999, uses the same data link layer protocol and frame format as the original standard, but an OFDM based air interface (physical layer). It operates in the 5 GHz band with a maximum net data rate of 54 Mbit/s, plus error correction code, which yields realistic net achievable throughput in the mid-20 Mbit/s. It has seen widespread worldwide implementation, particularly within the corporate workspace.
Since the 2.4 GHz band is heavily used to the point of being crowded, using the relatively unused 5 GHz band gives 802.11a a significant advantage. However, this high carrier frequency also brings a disadvantage: the effective overall range of 802.11a is less than that of 802.11b/g. In theory, 802.11a signals are absorbed more readily by walls and other solid objects in their path due to their smaller wavelength, and, as a result, cannot penetrate as far as those of 802.11b. In practice, 802.11b typically has a higher range at low speeds (802.11b will reduce speed to 5.5 Mbit/s or even 1 Mbit/s at low signal strengths). 802.11a also suffers from interference, but locally there may be fewer signals to interfere with, resulting in less interference and better throughput.
The 802.11b standard has a maximum raw data rate of 11 Mbit/s, and uses the same media access method defined in the original standard. 802.11b products appeared on the market in early 2000, since 802.11b is a direct extension of the modulation technique defined in the original standard. The dramatic increase in throughput of 802.11b (compared to the original standard) along with simultaneous substantial price reductions led to the rapid acceptance of 802.11b as the definitive wireless LAN technology.
Devices using 802.11b experience interference from other products operating in the 2.4 GHz band. Devices operating in the 2.4 GHz range include microwave ovens, Bluetooth devices, baby monitors, cordless telephones, and some amateur radio equipment. As unlicensed intentional radiators in this ISM band, they must not interfere with and must tolerate interference from primary or secondary allocations (users) of this band, such as amateur radio.
In June 2003, a third modulation standard was ratified: 802.11g. This works in the 2.4 GHz band (like 802.11b), but uses the same OFDM based transmission scheme as 802.11a. It operates at a maximum physical layer bit rate of 54 Mbit/s exclusive of forward error correction codes, or about 22 Mbit/s average throughput. 802.11g hardware is fully backward compatible with 802.11b hardware, and therefore is encumbered with legacy issues that reduce throughput by ~21% when compared to 802.11a.
The then-proposed 802.11g standard was rapidly adopted in the market starting in January 2003, well before ratification, due to the desire for higher data rates as well as reductions in manufacturing costs. By summer 2003, most dual-band 802.11a/b products became dual-band/tri-mode, supporting a and b/g in a single mobile adapter card or access point. Details of making b and g work well together occupied much of the lingering technical process; in an 802.11g network, however, activity of an 802.11b participant will reduce the data rate of the overall 802.11g network.
Like 802.11b, 802.11g devices suffer interference from other products operating in the 2.4 GHz band, for example wireless keyboards.
In 2003, task group TGma was authorized to "roll up" many of the amendments to the 1999 version of the 802.11 standard. REVma or 802.11ma, as it was called, created a single document that merged 8 amendments (802.11a, b, d, e, g, h, i, j) with the base standard. Upon approval on March 8, 2007, 802.11REVma was renamed to the then-current base standard IEEE 802.11-2007.
802.11n is an amendment that improves upon the previous 802.11 standards by adding multiple-input multiple-output antennas (MIMO). 802.11n operates on both the 2.4 GHz and the 5 GHz bands. Support for 5 GHz bands is optional. Its net data rate ranges from 54 Mbit/s to 600 Mbit/s. The IEEE has approved the amendment, and it was published in October 2009. Prior to the final ratification, enterprises were already migrating to 802.11n networks based on the Wi-Fi Alliance's certification of products conforming to a 2007 draft of the 802.11n proposal.
In May 2007, task group TGmb was authorized to "roll up" many of the amendments to the 2007 version of the 802.11 standard. REVmb or 802.11mb, as it was called, created a single document that merged ten amendments (802.11k, r, y, n, w, p, z, v, u, s) with the 2007 base standard. In addition much cleanup was done, including a reordering of many of the clauses. Upon publication on March 29, 2012, the new standard was referred to as IEEE 802.11-2012.
IEEE 802.11ac-2013 is an amendment to IEEE 802.11, published in December 2013, that builds on 802.11n. Changes compared to 802.11n include wider channels (80 or 160 MHz versus 40 MHz) in the 5 GHz band, more spatial streams (up to eight versus four), higher-order modulation (up to 256-QAM vs. 64-QAM), and the addition of Multi-user MIMO (MU-MIMO). As of October 2013, high-end implementations support 80 MHz channels, three spatial streams, and 256-QAM, yielding a data rate of up to 433.3 Mbit/s per spatial stream, 1300 Mbit/s total, in 80 MHz channels in the 5 GHz band. Vendors have announced plans to release so-called "Wave 2" devices with support for 160 MHz channels, four spatial streams, and MU-MIMO in 2014 and 2015.
IEEE 802.11ad is an amendment that defines a new physical layer for 802.11 networks to operate in the 60 GHz millimeter wave spectrum. This frequency band has significantly different propagation characteristics than the 2.4 GHz and 5 GHz bands where Wi-Fi networks operate. Products implementing the 802.11ad standard are being brought to market under the WiGig brand name. The certification program is now being developed by the Wi-Fi Alliance instead of the now defunct Wireless Gigabit Alliance. The peak transmission rate of 802.11ad is 7 Gbit/s.
IEEE 802.11ad is a protocol used for very high data rates (about 8 Gbit/s) and for short range communication (about 1-10 meters).
TP-Link announced the world's first 802.11ad router in January 2016.
IEEE 802.11af, also referred to as "White-Fi" and "Super Wi-Fi", is an amendment, approved in February 2014, that allows WLAN operation in TV white space spectrum in the VHF and UHF bands between 54 and 790 MHz. It uses cognitive radio technology to transmit on unused TV channels, with the standard taking measures to limit interference for primary users, such as analog TV, digital TV, and wireless microphones. Access points and stations determine their position using a satellite positioning system such as GPS, and use the Internet to query a geolocation database (GDB) provided by a regional regulatory agency to discover what frequency channels are available for use at a given time and position. The physical layer uses OFDM and is based on 802.11ac. The propagation path loss as well as the attenuation by materials such as brick and concrete is lower in the UHF and VHF bands than in the 2.4 and 5 GHz bands, which increases the possible range. The frequency channels are 6 to 8 MHz wide, depending on the regulatory domain. Up to four channels may be bonded in either one or two contiguous blocks. MIMO operation is possible with up to four streams used for either space–time block code (STBC) or multi-user (MU) operation. The achievable data rate per spatial stream is 26.7 Mbit/s for 6 and 7 MHz channels, and 35.6 Mbit/s for 8 MHz channels. With four spatial streams and four bonded channels, the maximum data rate is 426.7 Mbit/s for 6 and 7 MHz channels and 568.9 Mbit/s for 8 MHz channels.
IEEE 802.11-2016 which was known as IEEE 802.11 REVmc,, is a revision based on IEEE 802.11-2012, incorporating 5 amendments (11ae, 11aa, 11ad, 11ac, 11af). In addition, existing MAC and PHY functions have been enhanced and obsolete features were removed or marked for removal. Some clauses and annexes have been renumbered.
IEEE 802.11ah, published in 2017, defines a WLAN system operating at sub-1 GHz license-exempt bands. Due to the favorable propagation characteristics of the low frequency spectra, 802.11ah can provide improved transmission range compared with the conventional 802.11 WLANs operating in the 2.4 GHz and 5 GHz bands. 802.11ah can be used for various purposes including large scale sensor networks, extended range hotspot, and outdoor Wi-Fi for cellular traffic offloading, whereas the available bandwidth is relatively narrow. The protocol intends consumption to be competitive with low power Bluetooth, at a much wider range.
IEEE 802.11ai is an amendment to the 802.11 standard that added new mechanisms for a faster initial link setup time.
IEEE 802.11aj is a rebanding of 802.11ad for use in the 45 GHz unlicensed spectrum available in some regions of the world (specifically China).
Alternatively known as China Milli-Meter Wave (CMMW).
IEEE 802.11aq is an amendment to the 802.11 standard that will enable pre-association discovery of services. This extends some of the mechanisms in 802.11u that enabled device discovery to further discover the services running on a device, or provided by a network.
IEEE 802.11ax is the successor to 802.11ac, and will increase the efficiency of WLAN networks. Currently in development, this project has the goal of providing 4x the throughput of 802.11ac at the user layer, having just 37% higher nominal data rates at the PHY layer.
IEEE 802.11ay is a standard that is being developed. It is an amendment that defines a new physical layer for 802.11 networks to operate in the 60 GHz millimeter wave spectrum. It will be an extension of the existing 11ad, aimed to extend the throughput, range and use-cases. The main use-cases include: indoor operation, out-door back-haul and short range communications. The peak transmission rate of 802.11ay is 20 Gbit/s. The main extensions include: channel bonding (2, 3 and 4), MIMO and higher modulation schemes.
Across all variations of 802.11, maximum achievable throughputs are given either based on measurements under ideal conditions or in the layer-2 data rates. However, this does not apply to typical deployments in which data is being transferred between two endpoints, of which at least one is typically connected to a wired infrastructure and the other endpoint is connected to an infrastructure via a wireless link.
This means that, typically, data frames pass an 802.11 (WLAN) medium, and are being converted to 802.3 (Ethernet) or vice versa. Due to the difference in the frame (header) lengths of these two media, the application's packet size determines the speed of the data transfer. This means applications that use small packets (e.g., VoIP) create dataflows with high-overhead traffic (i.e., a low goodput). Other factors that contribute to the overall application data rate are the speed with which the application transmits the packets (i.e., the data rate) and, of course, the energy with which the wireless signal is received. The latter is determined by distance and by the configured output power of the communicating devices.
The same references apply to the attached graphs that show measurements of UDP throughput. Each represents an average (UDP) throughput (please note that the error bars are there, but barely visible due to the small variation) of 25 measurements. Each is with a specific packet size (small or large) and with a specific data rate (10 kbit/s – 100 Mbit/s). Markers for traffic profiles of common applications are included as well. These figures assume there are no packet errors, which if occurring will lower transmission rate further.
802.11b, 802.11g, and 802.11n-2.4 utilize the 2.400–2.500 GHz spectrum, one of the ISM bands. 802.11a, 802.11n and 802.11ac use the more heavily regulated 4.915–5.825 GHz band. These are commonly referred to as the "2.4 GHz and 5 GHz bands" in most sales literature. Each spectrum is sub-divided into channels with a center frequency and bandwidth, analogous to the way radio and TV broadcast bands are sub-divided.
The 2.4 GHz band is divided into 14 channels spaced 5 MHz apart, beginning with channel 1, which is centered on 2.412 GHz. The latter channels have additional restrictions or are unavailable for use in some regulatory domains.
The channel numbering of the 5.725–5.875 GHz spectrum is less intuitive due to the differences in regulations between countries. These are discussed in greater detail on the list of WLAN channels.
In addition to specifying the channel center frequency, 802.11 also specifies (in Clause 17) a spectral mask defining the permitted power distribution across each channel. The mask requires the signal be attenuated a minimum of 20 dB from its peak amplitude at ±11 MHz from the centre frequency, the point at which a channel is effectively 22 MHz wide. One consequence is that stations can use only every fourth or fifth channel without overlap.
Availability of channels is regulated by country, constrained in part by how each country allocates radio spectrum to various services. At one extreme, Japan permits the use of all 14 channels for 802.11b, and 1–13 for 802.11g/n-2.4. Other countries such as Spain initially allowed only channels 10 and 11, and France allowed only 10, 11, 12, and 13; however, Europe now allow channels 1 through 13. North America and some Central and South American countries allow only 1 through 11.
Since the spectral mask defines only power output restrictions up to ±11 MHz from the center frequency to be attenuated by −50 dBr, it is often assumed that the energy of the channel extends no further than these limits. It is more correct to say that, given the separation between channels, the overlapping signal on any channel should be sufficiently attenuated to minimally interfere with a transmitter on any other channel. Due to the near-far problem a transmitter can impact (desense) a receiver on a "non-overlapping" channel, but only if it is close to the victim receiver (within a meter) or operating above allowed power levels. Conversely, a sufficiently distant transmitter on an overlapping channel can have little to no significant effect.
Confusion often arises over the amount of channel separation required between transmitting devices. 802.11b was based on direct-sequence spread spectrum (DSSS) modulation and utilized a channel bandwidth of 22 MHz, resulting in three "non-overlapping" channels (1, 6, and 11). 802.11g was based on OFDM modulation and utilized a channel bandwidth of 20 MHz. This occasionally leads to the belief that four "non-overlapping" channels (1, 5, 9, and 13) exist under 802.11g, although this is not the case as per 184.108.40.206 Channel Numbering of operating channels of the IEEE Std 802.11 (2012), which states "In a multiple cell network topology, overlapping and/or adjacent cells using different channels can operate simultaneously without interference if the distance between the center frequencies is at least 25 MHz." and section 220.127.116.11 and Figure 18-13.
This does not mean that the technical overlap of the channels recommends the non-use of overlapping channels. The amount of inter-channel interference seen on a configuration using channels 1, 5, 9, and 13 (which is permitted in Europe, but not in North America) is barely different from a three-channel configuration, but with an entire extra channel.
However, overlap between channels with more narrow spacing (e.g. 1, 4, 7, 11 in North America) may cause unacceptable degradation of signal quality and throughput, particularly when users transmit near the boundaries of AP cells.
IEEE uses the phrase regdomain to refer to a legal regulatory region. Different countries define different levels of allowable transmitter power, time that a channel can be occupied, and different available channels. Domain codes are specified for the United States, Canada, ETSI (Europe), Spain, France, Japan, and China.
Most Wi-Fi certified devices default to regdomain 0, which means least common denominator settings, i.e., the device will not transmit at a power above the allowable power in any nation, nor will it use frequencies that are not permitted in any nation.
The regdomain setting is often made difficult or impossible to change so that the end users do not conflict with local regulatory agencies such as the United States' Federal Communications Commission.
The datagrams are called frames. Current 802.11 standards specify frame types for use in transmission of data as well as management and control of wireless links.
Frames are divided into very specific and standardized sections. Each frame consists of a MAC header, payload, and frame check sequence (FCS). Some frames may not have a payload.
The first two bytes of the MAC header form a frame control field specifying the form and function of the frame. This frame control field is subdivided into the following sub-fields:
The next two bytes are reserved for the Duration ID field. This field can take one of three forms: Duration, Contention-Free Period (CFP), and Association ID (AID).
An 802.11 frame can have up to four address fields. Each field can carry a MAC address. Address 1 is the receiver, Address 2 is the transmitter, Address 3 is used for filtering purposes by the receiver. Address 4 is only present in data frames transmitted between access points in an Extended Service Set or between intermediate nodes in a mesh network.
The remaining fields of the header are:
The payload or frame body field is variable in size, from 0 to 2304 bytes plus any overhead from security encapsulation, and contains information from higher layers.
The Frame Check Sequence (FCS) is the last four bytes in the standard 802.11 frame. Often referred to as the Cyclic Redundancy Check (CRC), it allows for integrity check of retrieved frames. As frames are about to be sent, the FCS is calculated and appended. When a station receives a frame, it can calculate the FCS of the frame and compare it to the one received. If they match, it is assumed that the frame was not distorted during transmission.
Management frames are not always authenticated, and allow for the maintenance, or discontinuance, of communication. Some common 802.11 subtypes include:
The body of a management frame consists of frame-subtype-dependent fixed fields followed by a sequence of information elements (IEs).
The common structure of an IE is as follows:
← 1 → ← 1 → ← 1-252 → ---------------------------- | Type |Length| Data | ----------------------------
Control frames facilitate in the exchange of data frames between stations. Some common 802.11 control frames include:
Data frames carry packets from web pages, files, etc. within the body. The body begins with an IEEE 802.2 header, with the Destination Service Access Point (DSAP) specifying the protocol, followed by a Subnetwork Access Protocol (SNAP) header if the DSAP is hex AA, with the organizationally unique identifier (OUI) and protocol ID (PID) fields specifying the protocol. If the OUI is all zeroes, the protocol ID field is an EtherType value. Almost all 802.11 data frames use 802.2 and SNAP headers, and most use an OUI of 00:00:00 and an EtherType value.
Similar to TCP congestion control on the internet, frame loss is built into the operation of 802.11. To select the correct transmission speed or Modulation and Coding Scheme, a rate control algorithm may test different speeds. The actual packet loss rate of an Access points vary widely for different link conditions. There are variations in the loss rate experienced on production Access points, between 10% and 80%, with 30% being a common average. It is important to be aware that the link layer should recover these lost frames. If the sender does not receive an Acknowledgement (ACK) frame, then it will be resent.
802.11F and 802.11T are recommended practices rather than standards, and are capitalized as such.
802.11m is used for standard maintenance. 802.11ma was completed for 802.11-2007, 802.11mb for 802.11-2012, and 802.11mc for 802.11-2016.
Both the terms "standard" and "amendment" are used when referring to the different variants of IEEE standards.
As far as the IEEE Standards Association is concerned, there is only one current standard; it is denoted by IEEE 802.11 followed by the date that it was published. IEEE 802.11-2016 is the only version currently in publication, superseding previous releases. The standard is updated by means of amendments. Amendments are created by task groups (TG). Both the task group and their finished document are denoted by 802.11 followed by a non-capitalized letter, for example, IEEE 802.11a and IEEE 802.11b. Updating 802.11 is the responsibility of task group m. In order to create a new version, TGm combines the previous version of the standard and all published amendments. TGm also provides clarification and interpretation to industry on published documents. New versions of the IEEE 802.11 were published in 1999, 2007, 2012, and 2016.
Various terms in 802.11 are used to specify aspects of wireless local-area networking operation, and may be unfamiliar to some readers.
For example, Time Unit (usually abbreviated TU) is used to indicate a unit of time equal to 1024 microseconds. Numerous time constants are defined in terms of TU (rather than the nearly equal millisecond).
Also the term "Portal" is used to describe an entity that is similar to an 802.1H bridge. A Portal provides access to the WLAN by non-802.11 LAN STAs.
In 2001, a group from the University of California, Berkeley presented a paper describing weaknesses in the 802.11 Wired Equivalent Privacy (WEP) security mechanism defined in the original standard; they were followed by Fluhrer, Mantin, and Shamir's paper titled "Weaknesses in the Key Scheduling Algorithm of RC4". Not long after, Adam Stubblefield and AT&T publicly announced the first verification of the attack. In the attack, they were able to intercept transmissions and gain unauthorized access to wireless networks.
The IEEE set up a dedicated task group to create a replacement security solution, 802.11i (previously this work was handled as part of a broader 802.11e effort to enhance the MAC layer). The Wi-Fi Alliance announced an interim specification called Wi-Fi Protected Access (WPA) based on a subset of the then current IEEE 802.11i draft. These started to appear in products in mid-2003. IEEE 802.11i (also known as WPA2) itself was ratified in June 2004, and uses the Advanced Encryption Standard AES, instead of RC4, which was used in WEP. The modern recommended encryption for the home/consumer space is WPA2 (AES Pre-Shared Key), and for the enterprise space is WPA2 along with a RADIUS authentication server (or another type of authentication server) and a strong authentication method such as EAP-TLS.
In December 2011, a security flaw was revealed that affects some wireless routers with a specific implementation of the optional Wi-Fi Protected Setup (WPS) feature. While WPS is not a part of 802.11, the flaw allows an attacker within the range of the wireless router to recover the WPS PIN and, with it, the router's 802.11i password in a few hours.
In late 2014, Apple announced that its iOS 8 mobile operating system would scramble MAC addresses during the pre-association stage to thwart retail footfall tracking made possible by the regular transmission of uniquely identifiable probe requests.
Many companies implement wireless networking equipment with non-IEEE standard 802.11 extensions either by implementing proprietary or draft features. These changes may lead to incompatibilities between these extensions.
This amendment defines standardized modifications to both the IEEE 802.11 physical layers (PHY) and the IEEE 802.11 medium access control layer (MAC) that enables at least one mode of operation capable of supporting a maximum throughput of at least 20 gigabits per second (measured at the MAC data service access point), while maintaining or improving the power efficiency per station.
Carrier-sense multiple access with collision avoidance (CSMA/CA) in computer networking, is a network multiple access method in which carrier sensing is used, but nodes attempt to avoid collisions by beginning transmission only after the channel is sensed to be "idle". When they do transmit, nodes transmit their packet data in its entirety.
It is particularly important for wireless networks, where the collision detection of the alternative CSMA/CD is not possible due to wireless transmitters desensing their receivers during packet transmission.
CSMA/CA is unreliable due to the hidden node problem.CSMA/CA is a protocol that operates in the Data Link Layer (Layer 2) of the OSI model.IEEE 802.11 (legacy mode)
IEEE 802.11 (legacy mode) – or more correctly IEEE 802.11-1997 or IEEE 802.11-1999 – refer to the original version of the IEEE 802.11 wireless networking standard released in 1997 and clarified in 1999. Most of the protocols described by this early version are rarely used today.IEEE 802.11a-1999
IEEE 802.11a-1999 or 802.11a was an amendment to the IEEE 802.11 wireless local network specifications that defined requirements for an orthogonal frequency division multiplexing (OFDM) communication system. It was originally designed to support wireless communication in the unlicensed national information infrastructure (U-NII) bands (in the 5–6 GHz frequency range) as regulated in the United States by the Code of Federal Regulations, Title 47, Section 15.407.
Originally described as clause 17 of the 1999 specification, it is now defined in clause 18 of the 2012 specification and provides protocols that allow transmission and reception of data at rates of 1.5 to 54Mbit/s. It has seen widespread worldwide implementation, particularly within the corporate workspace. While the original amendment is no longer valid, the term "802.11a" is still used by wireless access point (cards and routers) manufacturers to describe interoperability of their systems at 5.8 GHz, 54 Mbit/s (54 x 106 bits per second).
802.11 is a set of IEEE standards that govern wireless networking transmission methods. They are commonly used today in their 802.11a, 802.11b, 802.11g, 802.11n and 802.11ac versions to provide wireless connectivity in the home, office and some commercial establishments. Wi-Fi 2 is an unofficial retronym for 802.11a.IEEE 802.11ai
IEEE 802.11ai is a Wireless LAN study group in the IEEE that since June 2017 has standardized a fast initial link setup (FILS) function that enable a wireless LAN client to achieve a secure link setup within 100ms.
RevCom & Standards Board approval was expected in September 2016.IEEE 802.11b-1999
IEEE 802.11b-1999 or 802.11b, is an amendment to the IEEE 802.11 wireless networking specification that extends throughput up to 11 Mbit/s using the same 2.4GHz band. A related amendment was incorporated into the IEEE 802.11-2007 standard.
802.11 is a set of IEEE standards that govern wireless networking transmission methods. They are commonly used today in their 802.11a, 802.11b, 802.11g, 802.11n and 802.11ac versions to provide wireless connectivity in the home, office and some commercial establishments. Wi-Fi 1 is an unofficial retronym for 802.11b.IEEE 802.11c
IEEE 802.11c is an amendment to the IEEE 802.1D MAC bridging standard to incorporate bridging in wireless bridges or access points. This work is now part of IEEE 802.1D-2004.
802.11c was ratified in October 1998 and is a supplement to IEEE 802.1D that adds requirements associated with bridging 802.11 wireless client devices. In particular it adds a sub clause under 2.5 Support of the Internal Sublayer Service, to cover bridge operations with 802.11 MACs.IEEE 802.11d-2001
IEEE 802.11d-2001 is an amendment to the IEEE 802.11 specification that adds support for "additional regulatory domains". This support includes the addition of a country information element to beacons, probe requests, and probe responses. The country information elements simplifies the creation of 802.11 wireless access points and client devices that meet the different regulations enforced in various parts of the world. The amendment has been incorporated into the published IEEE 802.11-2012 standard.
802.11 is a set of IEEE standards that govern wireless networking transmission methods. They are commonly used today in their 802.11a, 802.11b, 802.11g, 802.11n, and 802.11ac, versions to provide wireless connectivity in the home, office and some commercial establishments.
802.11d is a wireless specification for operation in additional regulatory domains. This supplement to the 802.11 specifications defines the physical layer requirements:
New values for current MIB attributes
Future requirements to extend the operation of 802.11 WLANs to new regulatory domains (countries).The current 802.11 standard defines operation in only a few regulatory domains (countries). This supplement adds the requirements and definitions necessary to allow 802.11 WLAN equipment to operate in markets not served by the current standard. These are anything other than Americas or FCC, Europe or ETSI, Japan, China, Israel, Singapore, Taiwan.As of January 1, 2015, the U.S. Federal Communications Commission ruled that new devices are not allowed to rely solely on 802.11d for setting country-specific radio parameters.IEEE 802.11g-2003
IEEE 802.11g-2003 or 802.11g is an amendment to the IEEE 802.11 specification that extended throughput to up to 54 Mbit/s using the same 2.4 GHz band as 802.11b. This specification under the marketing name of Wi-Fi has been implemented all over the world. The 802.11g protocol is now Clause 19 of the published IEEE 802.11-2007 standard, and Clause 19 of the published IEEE 802.11-2012 standard.
802.11 is a set of IEEE standards that govern wireless networking transmission methods. They are commonly used today in their 802.11a, 802.11b, 802.11g, 802.11n and 802.11ac versions to provide wireless connectivity in the home, office and some commercial establishments. Wi-Fi 3 is an unofficial retronym for 802.11g.IEEE 802.11h-2003
IEEE 802.11h-2003, or just 802.11h, refers to the amendment added to the IEEE 802.11 standard for Spectrum and Transmit Power Management Extensions. It solves problems like interference with satellites and radar using the same 5 GHz frequency band. It was originally designed to address European regulations but is now applicable in many other countries. The standard provides Dynamic Frequency Selection (DFS) and Transmit Power Control (TPC) to the 802.11a PHY. It has been integrated into the full IEEE 802.11-2007 standard.
IEEE 802.11 is a set of IEEE standards that govern wireless networking transmission methods. They are commonly used today in their 802.11a, 802.11b, 802.11g, 802.11n and 802.11ac versions to provide wireless connectivity in the home, office, and some commercial establishments.IEEE 802.11i-2004
IEEE 802.11i-2004, or 802.11i for short, is an amendment to the original IEEE 802.11, implemented as Wi-Fi Protected Access II (WPA2). The draft standard was ratified on 24 June 2004. This standard specifies security mechanisms for wireless networks, replacing the short Authentication and privacy clause of the original standard with a detailed Security clause. In the process, the amendment deprecated broken Wired Equivalent Privacy (WEP), while it was later incorporated into the published IEEE 802.11-2007 standard.IEEE 802.11j-2004
802.11j-2004 or 802.11j is an amendment to the IEEE 802.11 standard designed specially for Japanese market. It allows Wireless LAN operation in the 4.9 to 5 GHz band to conform to the Japanese rules for radio operation for indoor, outdoor and mobile applications. The amendment has been incorporated into the published IEEE 802.11-2007 standard.
802.11 is a set of IEEE standards that govern wireless networking transmission methods. They are commonly used today in their 802.11a, 802.11b, 802.11g and 802.11n versions to provide wireless connectivity in the home, office and some commercial establishments.IEEE 802.11k-2008
IEEE 802.11k-2008 is an amendment to IEEE 802.11-2007 standard for radio resource management. It defines and exposes radio and network information to facilitate the management and maintenance of a mobile Wireless LAN. IEEE 802.11k was incorporated in IEEE Std 802.11-2012; see IEEE 802.11.IEEE 802.11p
IEEE 802.11p is an approved amendment to the IEEE 802.11 standard to add wireless access in vehicular environments (WAVE), a vehicular communication system. It defines enhancements to 802.11 (the basis of products marketed as Wi-Fi) required to support Intelligent Transportation Systems (ITS) applications. This includes data exchange between high-speed vehicles and between the vehicles and the roadside infrastructure, so called V2X communication, in the licensed ITS band of 5.9 GHz (5.85-5.925 GHz). IEEE 1609 is a higher layer standard based on the IEEE 802.11p. It is also the basis of a European standard for vehicular communication known as ETSI ITS-G5.IEEE 802.11r-2008
IEEE 802.11r-2008 or fast BSS transition (FT), also called fast roaming, is an amendment to the IEEE 802.11 standard to permit continuous connectivity aboard wireless devices in motion, with fast and secure handoffs from one base station to another managed in a seamless manner. It was published on July 15, 2008. IEEE 802.11r-2008 was rolled up into 802.11-2012.IEEE 802.11s
IEEE 802.11s is Wireless LAN standard and an IEEE 802.11 amendment for mesh networking, defining how wireless devices can interconnect to create a WLAN mesh network, which may be used for relatively fixed (not mobile) topologies and wireless ad hoc networks. The IEEE 802.11s working group draws upon volunteers from university and industry to provide specifications and possible design solutions for wireless mesh networking. As a standard, the document was iterated and revised many times prior to finalization.
802.11 is a set of IEEE standards that govern wireless networking transmission methods. They are commonly used today in their 802.11a, 802.11b, 802.11g, 802.11n and 802.11ac versions to provide wireless connectivity in the home, office and some commercial establishments.IEEE 802.11u
IEEE 802.11u-2011 is an amendment to the IEEE 802.11-2007 standard to add features that improve interworking with external networks.
802.11 is a family of IEEE technical standards for mobile communication devices such as laptop computers or multi-mode phones to join a wireless local area network (WLAN) widely used in the home, public hotspots and commercial establishments.
The IEEE 802.11u standard was published on February 25, 2011.IEEE 802.11v
IEEE 802.11v is an amendment to the IEEE 802.11 standard to allow configuration of client devices while connected to wireless networks. It was published as 802.11v-2011 and later incorporated into 802.11-2012 802.11 is a set of IEEE standards that govern wireless networking transmission methods. They are commonly used today in their 802.11a, 802.11b, 802.11g, 802.11n, and 802.11ac versions to provide wireless connectivity in the home, office and some commercial establishments.IEEE 802.11w-2009
IEEE 802.11w-2009 is an approved amendment to the IEEE 802.11 standard to increase the security of its management frames.Inter-Access Point Protocol
Inter-Access Point Protocol or IEEE 802.11F is a recommendation that describes an optional extension to IEEE 802.11 that provides wireless access point communications among multivendor systems. 802.11 is a set of IEEE standards that govern wireless networking transmission methods. They are commonly used today in their 802.11a, 802.11b, 802.11g and 802.11n versions to provide wireless connectivity in the home, office and some commercial establishments.
The IEEE 802.11 standard doesn't specify the communications between access points in order to support users roaming from one access point to another and load balancing. The 802.11 working group purposely did not define this element in order to provide flexibility in working with different wired and wireless distribution systems (i.e., wired backbones that interconnect access points).
IEEE 802.11 network PHY standards
|Frequency||Bandwidth||Stream data rate||Allowable
|1-6GHz||DSSS/FHSS||802.11-1997||Jun 1997||2.4||22||1, 2||N/A||DSSS, FHSS||20 m (66 ft)||100 m (330 ft)|
|HR-DSSS||802.11b||Sep 1999||2.4||22||1, 2, 5.5, 11||N/A||DSSS||35 m (115 ft)||140 m (460 ft)|
|OFDM||802.11a||Sep 1999||5||5/10/20||6, 9, 12, 18, 24, 36, 48, 54
(for 20MHz bandwidth,
divide by 2 and 4 for 10 and 5 MHz)
|N/A||OFDM||35 m (115 ft)||120 m (390 ft)|
|802.11p||Jul 2010||5.9||?||1,000 m (3,300 ft)|
|802.11y||Nov 2008||3.7[A]||?||5,000 m (16,000 ft)[A]|
|ERP-OFDM(, etc.)||802.11g||Jun 2003||2.4||38 m (125 ft)||140 m (460 ft)|
|HT-OFDM||802.11n||Oct 2009||2.4/5||20||Up to 288.8[B]||4||MIMO-OFDM||70 m (230 ft)||250 m (820 ft)|
|40||Up to 600[B]|
|VHT-OFDM||802.11ac||Dec 2013||5||20||Up to 346.8[B]||8||MIMO-OFDM||35 m (115 ft)||?|
|40||Up to 800[B]|
|80||Up to 1733.2[B]|
|160||Up to 3466.8[B]|
|HE-OFDM||802.11ax||Est. Dec 2019||2.4/5/6||?||Up to 10,530 (10.53 Gbit/s)||?||MIMO-OFDM||?||?|
|mmWave||DMG||802.11ad||Dec 2012||60||2,160||Up to 6,757
|N/A||OFDM, single carrier, low-power single carrier||3.3 m (11 ft)||?|
|802.11aj||Apr 2018||45/60[C]||540/1,080||Up to 15,000
|4||OFDM, single carrier||?||?|
|EDMG||802.11ay||Est. May 2020||60||8000||Up to 20,000 (20 Gbit/s)||4||OFDM, single carrier||10 m (33 ft)||100 m (328 ft)|
|sub-1GHz IoT||TVHT||802.11af||Feb 2014||0.054–0.79||6–8||Up to 568.9||4||MIMO-OFDM||?||?|
|S1G||802.11ah||Dec 2016||0.7/0.8/0.9||1–16||Up to 8.67 (@2 MHz)||4||?||?|
|?||802.11ba[E]||Est. Sep 2020||Other 802.11 protocol frequencies||narrow-
|light||IR||802.11-1997||Jun 1997||?||?||1, 2||N/A||PPM||?||?|
|?||802.11bb||Est. Jul 2021||380-5000nm band||?||?||N/A||?||?||?|
|802.11 Standard rollups|
|802.11-2007||Mar 2007||2.4, 5||Up to 54||DSSS, OFDM|
|802.11-2012||Mar 2012||2.4, 5||Up to 150[B]||DSSS, OFDM|
|802.11-2016||Dec 2016||2.4, 5, 60||Up to 866.7 or 6,757[B]||DSSS, OFDM|
Spread spectrum in digital communications
|Spread spectrum methods|