A gun turret (or turret) is a location from which weapons can be fired that affords protection, visibility, and some cone of fire. A modern gun turret is generally a weapon mount that houses the crew or mechanism of a projectile-firing weapon and at the same time lets the weapon be aimed and fired in some degree of azimuth and elevation (cone of fire).
Rotating gun turrets protect the weapon and its crew as they rotate. When this meaning of the word "turret" started being used at the beginning of the 1860s, turrets were normally cylindrical. Barbettes were an alternative to turrets; with a barbette the protection was fixed, and the weapon and crew were on a rotating platform inside the barbette. In the 1890s, armoured hoods (also known as "gun houses") were added to barbettes; these rotated with the platform (hence the term "hooded barbette"). By the early 20th Century, these hoods were known as turrets. Modern warships have gun-mountings described as turrets, though the "protection" on them is limited to protection from the weather.
Rotating turrets can be mounted on a fortified building or structure such as a coastal blockhouse, be part of a land battery, be mounted on a combat vehicle, a naval ship, or a military aircraft, they may be armed with one or more machine guns, automatic cannons, large-calibre guns, or missile launchers. They may be manned or remotely controlled and are most often protected to some degree, if not actually armoured.
The protection provided by the turret may be against battle damage, the weather conditions, general environment in which the weapon or its crew will be operating. The name derives from the pre-existing noun turret, from the French "touret", diminutive of the word "tower", meaning a self-contained protective position which is situated on top of a fortification or defensive wall as opposed to rising directly from the ground, in which case it constitutes a tower.
A small turret, or sub-turret set on top of a larger one, is called a cupola. The term cupola is also used for a rotating turret that carries a sighting device rather than weaponry, such as that used by a tank commander.[i]
Before the development of large-calibre, long-range guns in the mid-19th century, the classic battleship design[ii] used rows of gunport-mounted guns on each side of the ship, often mounted in casemates. Firepower was provided by a large number of guns, each of which could traverse only in a limited arc. Due to stability issues, fewer large (and thus heavy) guns can be carried high on a ship, but as this set casemates low and thus near the waterline they were vulnerable to flooding, effectively restricted their use to calm seas. Additionally casemate mounts had to be recessed into the side of a vessel to afford a wide arc of fire, and such recesses presented shot traps, compromising the integrity of armour plating.
Rotating turrets were weapon mounts designed to protect the crew and mechanism of the artillery piece and with the capability of being aimed and fired over a broad arc, typically between a three-quarter circle up to and including a full 360 degrees. These presented the opportunity to concentrate firepower in fewer, better-sited positions by eliminating redundancy, in other words combining the firepower of those guns unable to engage an enemy because they sited on the wrong beam into a more powerful, and more versatile unified battery.
Designs for a rotating gun turret date back to the late 18th century. In the mid 19th century, during the Crimean War, Captain Cowper Phipps Coles constructed a raft with guns protected by a 'cupola' and used the raft,[i] named the Lady Nancy, to shell the Russian town of Taganrog in the Black Sea. The Lady Nancy "proved a great success" and Coles patenting his rotating turret design after the war.
The British Admiralty ordered a prototype of Coles's patented design in 1859, which was installed in the ironclad floating battery, HMS Trusty, for trials in 1861, becoming the first warship to be fitted with a revolving gun turret. Coles's aim was to create a ship with the greatest possible all round arc of fire, as low in the water as possible to minimise the target.
The Admiralty accepted the principle of the turret gun as a useful innovation, and incorporated it into other new designs. Coles submitted a design for a ship having ten domed turrets each housing two large guns.
The design was rejected as impractical, although the Admiralty remained interested in turret ships and instructed its own designers to create better designs. Coles enlisted the support of Prince Albert, who wrote to the first Lord of the Admiralty, the Duke of Somerset, supporting the construction of a turret ship. In January 1862, the Admiralty agreed to construct a ship, HMS Prince Albert which had four turrets and a low freeboard, intended only for coastal defence.
While Coles designed the turrets, the ship was the responsibility of Chief Constructor Isaac Watts. Another ship using Coles' turret designs, HMS Royal Sovereign, was completed in August 1864. Its existing broadside guns were replaced with four turrets on a flat deck and the ship was fitted with 5.5 inches (140 mm) of armour in a belt around the waterline.
Early ships like the Royal Sovereign had little sea-keeping qualities being limited to coastal waters. Sir Edward James Reed, went on to design and build HMS Monarch, the first seagoing warship to carry her guns in turrets. Laid down in 1866 and completed in June 1869, it carried two turrets, although the inclusion of a forecastle and poop prevented the turret guns firing fore and aft.
The gun turret was independently invented by the Swedish inventor John Ericsson in America, while technologically inferior to Coles's version. Ericsson designed USS Monitor in 1861, its most prominent feature being a large cylindrical gun turret mounted amidships above the low-freeboard upper hull, also called the "raft". This extended well past the sides of the lower, more traditionally shaped hull.
A small armoured pilot house was fitted on the upper deck towards the bow, however, its position prevented Monitor from firing her guns straight forward. [iii] Like Coles, one of Ericsson's goals in designing the ship was to present the smallest possible target to enemy gunfire. The turret's rounded shape helped to deflect cannon shot. A pair of donkey engines rotated the turret through a set of gears; a full rotation was made in 22.5 seconds during testing on 9 February 1862 but fine control of the turret proved to be difficult as the engine would have to be placed in reverse if the turret overshot its mark or another full rotation could be made.
Including the guns, the turret weighed approximately 160 long tons (163 t); the entire weight rested on an iron spindle that had to be jacked up using a wedge before the turret was free to rotate. The spindle was 9 inches (23 cm) in diameter which gave it ten times the strength needed in preventing the turret from sliding sideways.
The gap between the turret and the deck proved to be another kind of problem for several Passaic-class monitors, which used the same turret design, as debris and shell fragments entered the gap and jammed the turrets during the First Battle of Charleston Harbor in April 1863. Direct hits at the turret with heavy shot also had the potential to bend the spindle, which could also jam the turret.
Monitor was originally intended to mount a pair of 15-inch (380 mm) smoothbore Dahlgren guns, but they were not ready in time and 11-inch (280 mm) guns were substituted, each gun weighing approximately 16,000 pounds (7,300 kg). Monitor's guns used the standard propellant charge of 15 pounds (6.8 kg) specified by the 1860 ordnance instructions for targets "distant", "near", and "ordinary", established by the gun's designer Dahlgren himself. They could fire a 136-pound (61.7 kg) round shot or shell up to a range of 3,650 yards (3,340 m) at an elevation of +15°.
HMS Thunderer (1872) represented the culmination of this pioneering work. An ironclad turret ship designed by Edward James Reed, it was equipped with revolving turrets that used pioneering hydraulic turret machinery to maneouvre the guns. It was also the world's first mastless battleship, built with a central superstructure layout, and became the prototype for all subsequent warships. With its sister HMS Devastation of 1871 it was another pivotal design, and led directly to the modern battleship.
The US Navy tried to save weight and allow the much faster firing 8-inch to shoot during the long reload time necessary for 12-inch guns by superposing secondary gun turrets directly on top of the primary turrets (as in the Kearsarge and Virginia-class battleships), but the idea proved to be practically unworkable and was soon abandoned.[iv]
With the advent of the South Carolina-class battleships in 1908, the main battery turrets were designed so as to superfire, to improve fire arcs on centerline mounted weapons. This was necessitated by a need to move all main battery turrets to the vessel's centerline for improved structural support. The 1906 HMS Dreadnought, while revolutionary in many other ways, had retained wing turrets due to concerns about muzzle blast affecting the sighting mechanisms of a turret below. A similar advancement was in the Kongō-class battlecruisers and Queen Elizabeth-class battleships, which dispensed with the "Q" turret amidships in favour of heavier guns in fewer mountings.
Like pre-dreadnoughts, the first dreadnoughts had two guns in each turret; however, later ships began to be fitted with triple turrets. The first ship to be built with triple turrets was the Italian Dante Alighieri, although the first to be actually commissioned was the Austro-Hungarian SMS Viribus Unitis of the Tegetthoff class. By the beginning of World War II, most battleships used triple or, occasionally, quadruple turrets, which reduced the total number of mountings and improved armour protection. However, quadruple turrets proved to be extremely complex to arrange, making them unwieldy in practice.
The largest warship turrets were in World War II battleships where a heavily armoured enclosure protected the large gun crew during battle. The calibre of the main armament on large battleships was typically 300 to 460 mm (12 to 18 in). The turrets carrying three 460 mm guns of Yamato each weighed around 2,500 tonnes. The secondary armament of battleships (or the primary armament of light cruisers) was typically between 127 and 152 mm (5.0 and 6.0 in). Smaller ships typically mounted guns from 76 mm (3.0 in) upwards, although these rarely required a turret mounting, except for large destroyers, like the American Fletcher and the German Narvik classes.
In naval terms, turret traditionally and specifically refers to a gun mounting where the entire mass rotates as one, and has a trunk that projects below the deck. The rotating part of a turret seen above deck is the gunhouse, which protects the mechanism and crew, and is where the guns are loaded. The gunhouse is supported on a bed of rotating rollers, and is not necessarily physically attached to the ship at the base of the rotating structure. In the case of the German battleship Bismarck, the turrets were not vertically restrained and fell out when she sank. The British battlecruiser Hood, like some American battleships, did have vertical restraints.
Below the gunhouse there may be a working chamber, where ammunition is handled, and the main trunk, which accommodates the shell and propellant hoists that bring ammunition up from the magazines below. There may be a combined hoist (cf the animated British turret) or separate hoists (cf the US turret cutaway). The working chamber and trunk rotate with the gunhouse, and sit inside a protective armoured barbette. The barbette extends down to the main armoured deck (red in the animation). At the base of the turret sit handing rooms, where shell and propelling charges are passed from the shell room and magazine to the hoists.
The handling equipment and hoists are complex arrangements of machinery that transport the shells and charges from the magazine into the base of the turret. Bearing in mind that shells can weigh around a ton, the hoists have to be powerful and rapid; a 15-inch turret of the type in the animation was expected to perform a complete loading and firing cycle in a minute.
The loading system is fitted with a series of mechanical interlocks that ensure that there is never an open path from the gunhouse to the magazine down which an explosive flash might pass. Flash-tight doors and scuttles open and close to allow the passage between areas of the turret. Generally, with large-calibre guns, powered or assisted ramming is required to force the heavy shell and charge into the breech.
As the hoist and breech must be aligned for ramming to occur, there is generally a restricted range of elevations at which the guns can be loaded; the guns return to the loading elevation, are loaded, then return to the target elevation, at which time they are said to be "in battery". The animation illustrates a turret where the rammer is fixed to the cradle that carries the guns, allowing loading to occur across a wider range of elevations.
Earlier turrets differed significantly in their operating principles. It was not until the last of the "rotating drum" designs described in the previous section were phased out that the "hooded barbette" arrangement above became the standard.
A wing turret is a gun turret mounted along the side, or the wings, of a warship, off the centerline.
The positioning of a wing turret limits the gun's arc of fire, so that it generally can contribute to only the broadside weight of fire on one side of the ship. This is the major weakness of wing turrets as broadsides were the most prevalent type of gunnery duels. Depending on the configurations of ships, such as HMS Dreadnought but not SMS Blücher, the wing turrets could fire fore and aft, so this somewhat reduced the danger when an opponent crossed the T enabling it to fire a full broadside.
Attempts were made to mount turrets en echelon so that they could fire on either beam, such as the Invincible-class and SMS Von der Tann battlecruisers, but this tended to cause great damage to the ships' deck from the muzzle blast.
Wing turrets were commonplace on capital ships and cruisers during the late 19th century up until the early 1910s. In pre-dreadnought battleships, the wing turret contributed to the secondary battery of sub-calibre weapons. In large armoured cruisers, wing turrets contributed to the main battery, although the casemate mounting was more common. At the time, large numbers of smaller calibre guns contributing to the broadside were thought to be of great value in demolishing a ship's upperworks and secondary armaments, as distances of battle were limited by fire control and weapon performance.
In the early 1900s, weapon performance, armour quality and vessel speeds generally increased along with the distances of engagement; the utility of large secondary batteries reducing as a consequence, and in addition at extreme range it was impossible to see the fall of lesser weapons and so correct the aim. Therefore, most early dreadnought battleships featured "all big gun" armaments of identical calibre, typically 11 or 12 inches, some of which were mounted in wing turrets. This arrangement was not satisfactory, however, as the wing turrets not only had a reduced fire arc for broadsides, but also because the weight of the guns put great strain on the hull and it was increasingly difficult to properly armour them.
Larger and later dreadnought battleships carried superimposed or superfiring turrets (i.e. one turret mounted higher than and firing over those in front of and below it). This allowed all turrets to train on either beam, and increased the weight of fire forward and aft. The superfiring or superimposed arrangement had not been proven until after South Carolina went to sea, and it was initially feared that the weakness of the previous Virginia-class ship's stacked turrets would repeat itself. Larger and later guns (such as the US Navy's ultimate big gun design, the 16"/50 Mark 7) also could not be shipped in wing turrets, as the strain on the hull would have been too great.
Many modern surface warships have mountings for large calibre guns, although the calibres are now generally between 3 and 5 inches (76 and 127 mm). The gunhouses are often just weatherproof covers for the gun mounting equipment and are made of light un-armoured materials such as glass-reinforced plastic. Modern turrets are often automatic in their operation, with no humans working inside them and only a small team passing fixed ammunition into the feed system. Smaller calibre weapons often operate on the autocannon principle, and indeed may not even be turrets at all; they may just be bolted directly to the deck.
On board warships, each turret is given an identification. In the British Royal Navy, these would be letters: "A" and "B" were for the turrets from the front of the ship backwards in front of the bridge, and letters near the end of the alphabet (i.e., "X", "Y", etc.) were for turrets behind the bridge ship, "Y" being the rearmost. Mountings in the middle of the ship would be "P", "Q", "R", etc. Confusingly, the Dido-class cruisers had a "Q" and the Nelson-class battleships had an "X" turret in what would logically be "C" position; the latter being mounted at the main deck level in front of the bridge and behind the "B" turret, thus having restricted training fore and aft.[v]
Exceptions were of course made; the battleship HMS Agincourt had the uniquely large number of seven turrets. These were numbered "1" to "7" but were unofficially nicknamed "Sunday", Monday", etc. through to "Saturday".
In German use, turrets were generally named "A", "B", "C", "D", "E", going from bow to stern. Usually the radio alphabet was used on naming the turrets (e.g. "Anton", "Bruno" or "Berta", "Caesar", "Dora") as on the German battleship Bismarck.
During World War I, air gunners initially operated guns that were mounted on pedestals or swivel mounts known as pintles. The latter evolved into the Scarff ring, a rotating ring mount which allowed the gun to be turned to any direction with the gunner remaining directly behind it, the weapon held in an intermediate elevation by bungee cord, a simple and effective mounting for single weapons such as the Lewis Gun though less handy when twin mounted as with the British Bristol F.2 Fighter and German "CL"-class two-seaters such as the Halberstadt and Hannover-designed series of compact two-seat combat aircraft. In a failed 1916 experiment, a variant of the SPAD S.A two-seat fighter was probably the first aircraft to be fitted with a remotely-controlled gun, which was located in a nose nacelle.
As aircraft flew higher and faster, the need for protection from the elements led to the enclosure or shielding of the gun positions, as in the "lobsterback" rear seat of the Hawker Demon biplane fighter.
The first British operational bomber to carry an enclosed, power-operated turret was the British Boulton & Paul Overstrand twin-engined biplane, which first flew in 1933. The Overstrand was similar to its First World War predecessors in that it had open cockpits and hand-operated defensive machine guns. However, unlike its predecessors, the Sidestrand could fly at 140 mph (225 km/h) making operating the exposed gun positions difficult, particularly in the aircraft's nose. To overcome this problem, the Overstrand was fitted with an enclosed and powered nose turret, mounting a single Lewis gun. As such the Overstrand was the first British aircraft to have a power-operated turret. Rotation was handled by pneumatic motors while elevation and depression of the gun used hydraulic rams. The pilot's cockpit was also enclosed but the dorsal (upper) and ventral (belly) gun positions remained open, though shielded.
The Martin B-10 all-metal monocoque monoplane bomber introduced turret-mounted defensive armament within the United States Army Air Corps, almost simultaneously with the RAF's Overstrand biplane bomber design. The Martin XB-10 prototype aircraft first featured the nose turret in June 1932—roughly a year before the less advanced Overstrand airframe design—and was first produced as the YB-10 service test version by November 1933. The production B-10B version started service with the USAAC in July 1935.
In time the number of turrets carried and the number of guns mounted increased. RAF heavy bombers of World War II such as the Handley Page Halifax (until its Mk II Series I (Special) version omitted the nose turret), Short Stirling and Avro Lancaster typically had three powered turrets: rear, mid-upper and nose. (Early in the war, some British heavy bombers also featured retractable, remotely-operated ventral (or mid-under) turret. The rear turret mounted the heaviest armament: four 0.303 inch Browning machine guns or, late in the war, two AN/M2 light-barrel versions of the US Browning M2 machine gun as in the Rose-Rice turret. The tail gunner or "Tail End Charlie" position was generally accepted to be the most dangerous assignment.
During the World War II era, British turrets were largely self-contained units, manufactured by Boulton Paul Aircraft and Nash & Thompson. The same model of turret might be fitted to several different aircraft types. Some models included gun-laying radar that could lead the target and compensate for bullet drop.
As almost a 1930s "updated" adaptation of the earlier Bristol F.2's concept, the UK introduced the concept of the "turret fighter", with aeroplanes such as the Boulton Paul Defiant and Blackburn Roc where the armament (four 0.303 inch) machineguns was in a turret mounted behind the pilot, rather than in fixed positions in the wings. The Defiant and Roc possessed no fixed, forward-firing automatic ordnance; the World War I-era Bristol F.2 was designed with one synchronized Vickers machine gun firing forward on a fuselage mount.
The concept came at a time when the standard armament of a fighter was only two machine guns and in the face of heavily armed bombers operating in formation, it was thought that a group of turret fighters would be able to concentrate their fire flexibly on the bombers; making beam, stern and rising attacks practicable. Although the idea had some merits in attacking bombers it made the turret fighter a sitting duck when facing fighters: the weight and drag penalty of the turret (and gunner) so reduced the power to weight ratio they operated at a huge disadvantage, one the theoretical flexibility of the turret armament could not compensate for, and this was at a time when British fighters were flying with 8 machine guns, while German fighters carried fewer machine guns but were also armed with automatic cannons.
Attempts to put this heavier armament, such as multiple 20 mm cannon in low profile aerodynamic turrets were explored by the British but were not successful, this class of weapons and heavier armament (up to and including artillery pieces as in the 1,420 examples produced of the American B-25G and B-25H Mitchell medium bombers, and the experimental 'Tsetse' variant of the de Haviland Mosquito) being exclusively fuselage or underwing-mounted and thus aimed by pointing the aircraft as a whole.
Not all turret designs put the gunner in the turret along with the armament: US and German-designed aircraft both featured remote-controlled turrets.
In the US, the large, purpose-built Northrop P-61 Black Widow night fighter was produced with a remotely operated dorsal turret that had a wide range of fire though in practice it was generally fired directly forward under control of the pilot. For the last Douglas-built production blocks of the B-17F (the "B-17F-xx-DL" designated blocks), and for all versions of the B-17G Flying Fortress a twin-gun remotely operated "chin" turret, designed by Bendix and first used on the experimental YB-40 "gunship" version of the Fortress, was added to give more forward defence. Specifically designed to be compact and not obstruct the bombardier, this was operated by a swing-away diagonal column possessing a yoke to traverse the turret, and aimed by a reflector sight mounted in the windscreen.
The intended replacement for the German Bf 110 heavy fighter, the Messerschmitt Me 210, possessed twin half-teardrop-shaped, remotely operated Ferngerichtete Drehringseitenlafette FDSL 131/1B turrets, one on each side "flank" of the rear fuselage to defend the rear of the aircraft, controlled from the rear area of the cockpit. By 1942, the German He 177A Greif heavy bomber would feature a Fernbedienbare Drehlafette FDL 131Z remotely operated forward dorsal turret, armed with twin 13mm MG 131 machine guns on the top of the fuselage, which was operated from a hemispherical, clear rotating "astrodome" just behind the cockpit glazing and offset to starboard atop the fuselage—a second, manned powered Hydraulische Drehlafette HDL 131 dorsal turret, further aft on the fuselage with a single MG 131 was also used on most examples.
The US B-29 Superfortress had four remote controlled turrets, comprising two dorsal and two ventral turrets. These were controlled from a trio of hemispherically glazed gunner-manned "astrodome" sighting stations operated from the pressurised sections in the nose and middle of the aircraft, each housing an altazimuth mounted pivoting gunsight to aim one or more of the unmanned remote turrets as needed, in addition to a B-17 style flexible manned tail gunner's station.
The defensive turret on bombers fell from favour with the realization that bombers could not attempt heavily defended targets without escort regardless of their defensive armament unless very high loss rates were acceptable, and the performance penalty from the weight and drag of turrets reduced speed, range and payload and increased the number of crew required. The already mentioned British de Havilland Mosquito light bomber was designed to operate without any defensive armament and used its speed to avoid engagement with fighters, much as the minimally armed German Schnellbomber aircraft concepts had been meant to do early in World War II.
A small number of aircraft continued to use turrets however—in particular maritime patrol aircraft such as the Avro Shackleton used one as an offensive weapon against small unarmoured surface targets. The Boeing B-52 jet bomber and many of its contemporaries (particularly Russian) featured a barbette (a British English term equivalent to the American usage of the term 'tail gun'), or a "remote turret"—an unmanned turret but often one with a more limited field of fire than a manned equivalent.
Aircraft carry their turrets in various locations:
Amongst the first armoured vehicles to be equipped with a gun turret were the Lanchester and Rolls-Royce Armoured Cars, both produced from 1914. The Royal Naval Air Service (RNAS) raised the first British armoured car squadron during the First World War. In September 1914 all available Rolls Royce Silver Ghost chassis were requisitioned to form the basis for the new armoured car. The following month a special committee of the Admiralty Air Department, among whom was Flight Commander T.G. Hetherington, designed the superstructure which consisted of armoured bodywork and a single fully rotating turret holding a regular water cooled Vickers machine gun.
However, the first tracked combat vehicles were not equipped with turrets due to the problems with getting sufficient trench crossing while keeping the centre of gravity low, and it was not until late in World War I that the French Renault FT light tank introduced the single fully rotating turret carrying the vehicle's main armament that continues to be the standard of almost every modern main battle tank and many post-World War II self-propelled guns. The first turret designed for the FT was a circular, cast steel version almost identical to that of the prototype. It was designed to carry a Hotchkiss 8mm machine gun. Meanwhile, the Berliet Company produced a new design, a polygonal turret of riveted plate, which was simpler to produce than the early cast steel turret. It was given the name "omnibus", since it could easily be adapted to mount either the Hotchkiss machine gun or the Puteaux 37mm with its telescopic sight. This turret was fitted to production models in large numbers.
In the 1930s, several nations produced multi-turreted tanks—probably influenced by the experimental British Vickers A1E1 Independent of 1926. Those that saw combat during the early part of World War II performed poorly and the concept was soon dropped. Combat vehicles without turrets, with the main armament mounted in the hull, or more often in a completely enclosed, integral armored casemate as part of the main hull, saw extensive use by both the German (as Sturmgeschütz and Jagdpanzer vehicles) and Soviet (as Samokhodnaya Ustanovka vehicles) armored forces during World War II as tank destroyers and assault guns. However, post-war, the concept fell out of favour due to its limitations, with the Swedish Stridsvagn 103 'S-Tank' and the German Kanonenjagdpanzer being exceptions.
In modern tanks, the turret is armoured for crew protection and rotates a full 360 degrees carrying a single large-calibre tank gun, typically in the range of 105 mm to 125 mm calibre. Machine guns may be mounted inside the turret, which on modern tanks is often on a "coaxial" mount, parallel with the larger main gun.
Early designs often featured multiple weapons mounts, and this concept was carried forwards into the early interwar years in Britain, Germany and the Soviet Union, arguably reaching its most absurd expression in the British 'Vickers A1E1 Independent tank, though this attempt was soon abandoned while the Soviet Union's similar effort produced a 'land battleship' which was actually produced and fought in defence of the Soviet Union.
In modern tanks, the turret houses all the crew except the driver (who is located in the hull). The crew located in the turret typically consist of tank commander, gunner, and often a gun loader (except in tanks that have an automated loading mechanism), while the driver sits in a separate compartment with a dedicated entry and exit, though often one that allows the driver to exit via the turret basket (fighting compartment).
For other combat vehicles, the turrets are equipped with other weapons dependent on role. An infantry fighting vehicle may carry a smaller calibre gun or an autocannon, or an anti-tank missile launcher, or a combination of weapons. A modern self-propelled gun mounts a large artillery gun but less armour. Lighter vehicles may carry a one-man turret with a single machine gun, occasionally the same model being shared with other classes of vehicle, such as the Cadillac Gage T50 turret/weapons station.
The size of the turret is a factor in combat vehicle design. One dimension mentioned in terms of turret design is "turret ring diameter" which is the size of the aperture in the top of the chassis into which the turret is seated.
In 1859, the Royal Commission on the Defence of the United Kingdom were in the process of recommending a huge programme of fortifications to protect Britain's naval bases. They interviewed Captain Coles, who had bombarded Russian fortifications during the Crimean War, however Coles repeatedly lost his temper during the discussion and the commissioners failed to ask him about the gun turret that he had patented earlier in that year, with the result that none of the Palmerston Forts mounted turrets. Eventually, the Admiralty Pier Turret at Dover was commissioned in 1877 and completed in 1882.
In continental Europe, the invention of high explosive shells in 1885 threatened to make all existing fortifications obsolete; a partial solution was the protection of fortress guns in armoured turrets. Pioneering designs were produced by Commandant Henri-Louis-Philippe Mougin in France and Captain Maximilian Schumann in Germany. Mougin's designs were incorporated in a new generation of polygonal forts constructed by Raymond Adolphe Séré de Rivières in France and Henri Alexis Brialmont in Belgium. Developed versions of Schumann's turrets were employed after his death in the fortifications of Metz. In 1914, the Brialmont forts in the Battle of Liège proved unequal to the German "Big Bertha" 42 cm siege howitzers, which were able to penetrate the turret armour and smash turret mountings.
Elsewhere, armoured turrets, sometimes described a cupolas, were incorporated into coastal artillery defences. An extreme example was Fort Drum, the "concrete battleship", near Corregidor, Philippines; this mounted four huge 14-inch guns in two naval pattern turrets and was the only permanent turreted fort ever constructed by the United States. Between the wars, improved turrets formed the offensive armament of the Maginot Line forts in France. During the Second World War, some of the artillery pieces in the Atlantic Wall fortifications, such as the Cross-Channel guns, were large naval guns housed in turrets.
Some nations, from Albania to Switzerland and Austria, have embedded the turrets of obsolete tanks in concrete bunkers, while others have constructed or updated fortifications with modern artillery systems, such as the 1970s era Swedish coastal artillery battery on Landsort Island.
ARM Durango (PO-151) is a Durango-class patrol vessel in the Mexican Navy with a main 57 mm gun turret and a helicopter landing pad, currently primarily used to fight drug cartels. It is also armed with SA-18 Grouse missiles. Like other ships of this class, it was designed and built in Mexican dockyards, and is sometimes referred to as a compact frigate. It was named after the Mexican state of DurangoARM Guanajuato
The ARM Guanajuato (PO-153) is a Durango-class oceanic patrol vessel in the Mexican Navy with a 57mm main gun turret and a helicopter landing pad, currently primarily used for drug interception and maritime security in Mexican territorial waters. It is also armed with SA-18 Grouse missiles. Like other ships of this class, it was designed and built in Mexican dockyards, and is sometimes referred to as a compact frigate. It was named after the Mexican state of Guanajuato.ARM Veracruz
ARM Veracruz (PO-151) is a Durango-class patrol vessel in service with the Mexican Navy with a 57 mm main gun turret and a helicopter landing pad, currently primarily used to fight drug cartels. It is also armed with SA-18 Grouse missiles. Like other ships of this class, it was designed and built in Mexican dockyards, and is sometimes referred to as a compact frigate.Altazimuth mount
An altazimuth or alt-azimuth mount is a simple two-axis mount for supporting and rotating an instrument about two perpendicular axes – one vertical and the other horizontal. Rotation about the vertical axis varies the azimuth (compass bearing) of the pointing direction of the instrument. Rotation about the horizontal axis varies the altitude (angle of elevation) of the pointing direction.
These mounts are used, for example, with telescopes, cameras, radio antennas, heliostat mirrors, solar panels, and guns and similar weapons.
Several names are given to this kind of mount, including altitude-azimuth, azimuth-elevation and various abbreviations thereof. A gun turret is essentially an alt-azimuth mount for a gun, and a standard camera tripod is an alt-azimuth mount as well.Austrått Fort
Austrått Fort is a disused coastal artillery site located at Austrått in Ørland, Norway. It was constructed in 1942 by the German Wehrmacht to protect the Trondheimsfjord during the German occupation of Norway during World War II. The fort's centrepiece is a triple 28 cm SK C/34 (11-inch) gun turret from the German battleship Gneisenau, which was damaged in Kiel. The three-gun turret weighs 800 tons and was capable of firing 730-pound shells 38 kilometres (24 mi). The last firing took place in 1953 and the fort was decommissioned in 1968. It opened as a museum in 1991.Like its sister battery at Sotra near Bergen, a shaft was cut out of the rocks for the huge former Gneisenau battleship gun turret. The triple 28cm SK C/34 turret became available after the discontinuation of the Kriegsmarine battleships building programme in 1942. Turret Anton was split up in three separate barrels and placed at Fort Rozenburg in the Netherlands. Turret Bruno was installed in a shaft on Sotra, Norway. Turret Caesar was emplaced halfway up occupied Norway. About 650 Yugoslavian slave laborers, mostly Serbs (Partisans and Chetniks) worked under awful conditions on the tunnels and bunkers around the hill. In a short time, a large underground system with supporting bunkers was finished. In August 1943 the guns were test-fired. No real engagements occurred during the remainder of the war, however.
The underground barracks and turret shaft with its ammunition rooms are open to the public. Because the Norwegians kept the site in operating condition until 1968, it remains in a good state of preservation. Today it is one of the most complete examples of a World
War II German coastal battery extant.
In addition, the site still has its infantry defenses consisting of trenches and a recently renovated 4.7cm French-made anti-tank gun in working condition. The gun covers an anti-tank wall through the woods intended to protect the entrance of the complex.BPM-97
The BPM-97 (Boyevaya Pogranichnaya Mashina - "Battle Vehicle of the Border Guard") or Выстрел (Vystrel) is the Russian military designation for the KAMAZ 43269 Vystrel 4×4 wheeled mine-resistant, ambush protected (MRAP) vehicle. It is produced fitted with several different turrets like the one of the BTR-80A. The vehicle is based on the KAMAZ-43269 and as the name suggests was designed for the Russian Border Guards. The latest model has bulletproof side windows and no gun turret. It has been ordered by Kazakhstan and by the National Guard of Russia, Federal Prison Service and EMERCOM.Barbette
Barbettes are several types of gun emplacement in terrestrial fortifications or on naval ships.
In recent naval usage, a barbette is a protective circular armour support for a heavy gun turret. This evolved from earlier forms of gun protection that eventually led to the pre-dreadnought. The name barbette ultimately comes from fortification - it originally meant a raised platform or mound, as in the French phrase en barbette, which refers to the practice of firing a cannon over a parapet rather than through an embrasure in a fortification's casemate. The former gives better angles of fire but less protection than the latter. The disappearing gun was a variation on the barbette gun; it consisted of a heavy gun on a carriage that would retract behind a parapet or into a gunpit for reloading. Barbettes were primarily used in coastal defences, but saw some use in a handful of warships, and some inland fortifications. The term is also used for certain aircraft gun mounts.
Shipboard barbettes were primarily used in armoured warships - starting in the 1860s during a period of intense experimentation with other mounting systems for heavy guns at sea. In these, gun barrels usually protruded over the barbette edge, so barbettes provided only partial protection, mainly for the ammunition supply. Alternatives included the heavily-armoured gun turret and an armoured, fixed central gun battery. By the late 1880s, all three systems were replaced with a hybrid barbette-turret system that combined the benefits of both types. The armoured vertical tube that supported the new gun mount was referred to as a barbette.
Guns with restricted arcs of fire mounted in heavy bombers during World War II—such those in the tail of the aircraft, as opposed to fully revolving turrets—were also sometimes referred to as having barbette mounts, though usage of the term is primarily restricted to British publications. American authors generally refer to such mounts as tail guns or as tail gun turrets.Bell 207 Sioux Scout
The Bell 207 Sioux Scout was a modified Bell 47 helicopter, developed by Bell Helicopter under contract from the United States Army, as a proof-of-concept demonstrator for the Bell D-255 helicopter gunship design, featuring a tandem cockpit, stub wings, and a chin-mounted gun turret.Caudron J Marine
The Caudron J Marine was an amphibious, two-seat, biplane equipped with floats and wheels, simiar to the earlier Caudron J floatplane.
The Caudron J was essentially a seaplane version of the two-seat Caudron G and single-seat Caudron F. The F, G and J all fllowed a similar layout with 2½ bay biplane wings, a tail-unit, with single fin and rudder, supported on struts attached to the wings at the first inter-plane struts and a central fuselage nacelle housing the cockpit and mounting the tractor engine. Two main floats were strut-supported under the wings and a small tail-float attached to the tail-unit. Power was supplied by a 100 hp (75 kW) Anzani 10-cylinder radial engine.The three production Caudron J Marine were used by the French Navy (la Marine Française) for reconnaissance and artillery observation. On 8 May 1914, René Caudron flew the second example from a wooden platform erected over a gun turret, on the French Navy cruiser Foudre. The first example was powered by a 100 hp (75 kW) Gnome 9 Delta rotary engine, with the remaining two powered by 80 hp (60 kW) Gnome 7 Lambda rotary engines.Fjell Fortress
Fjell Fortress (Norwegian: Fjell festning) is located on the island of Sotra in the municipality of Fjell, Hordaland county, Norway.HMS Roberts (F40)
HMS Roberts was a Royal Navy Roberts-class monitor of the Second World War. She was the second monitor to be named after Field Marshal Frederick Roberts, 1st Earl Roberts.
Built by John Brown & Company, of Clydebank, she was laid down 30 April 1940, launched 1 April 1941 and completed on 27 October 1941. She reused the twin 15-inch gun turret of the First World War monitor Marshal Soult.HNLMS Schorpioen
HNLMS Schorpioen is a Schorpioen-class monitor built in France for the Royal Netherlands Navy in the 1860s. These new ships were equipped with heavy rifled 23 cm (9 in) guns, and a heavy armor. The hull had an armor plated belt of 15 cm (6 in) and the gun turret, housing the two guns, had almost 30 cm (12 in) of armor.
She came from the building yard with two tripod masts and able to employ about 600 m2 (6,500 sq ft) of sails, but she proved to be a difficult sailing ship and some years later the yards, masts and the sails were removed. As with Buffel her huge steam engines gave her a maximum speed of 13 knots (24 km/h; 15 mph). Her striking weapon was the pointed ram bow, slightly different from Buffel's, but she never ever used this overestimated weapon.MG 131 machine gun
The MG 131 (shortened from German: Maschinengewehr 131, or "Machine gun 131") was a German 13 mm caliber machine gun developed in 1938 by Rheinmetall-Borsig and produced from 1940 to 1945. The MG 131 was designed for use at fixed, flexible or turreted, single or twin mountings in Luftwaffe aircraft during World War II.
It was one of the smallest, if not the smallest among the heavy machine guns, the weight was less than 60% of the M2 Browning or the Breda-SAFAT machine gun. Despite this, the MG 131 was a rapid fire weapon with an elevated firepower for its mass. It was equipped with HEI ammunition. The nearer equivalent could have been the Japanese Ho-103, itself based on the earlier American M1921 Browning machine gun. The other Axis main machine gun, the Breda 12.7 mm, was around 13 kg heavier and bigger, while slower by at least 150 rpm. The small size of the MG 131 meant the possibility to replace the 7.92 mm machine guns even in the small nose of the Luftwaffe fighters, which was commonplace from 1943 onwards. This weapon was a marked improvement as the greater armour protection Allied aircraft received rendered smaller calibers almost useless. This was especially true when it came to heavy Allied bombers.
It was installed in the Messerschmitt Bf 109, Me 410 Hornisse, Fw 190, Ju 88, Junkers Ju 388, He 177 Greif bomber variants, and many other aircraft. The Fernbedienbare Drehlafette FDL 131Z remotely controlled gun turret system, used either a single, or more commonly a "twinned" pair of MG 131s for dorsal defense. The quadmount Hecklafette HL 131V weapons "system" for tail defense, placing two MG 131 guns apiece in a pair of rotating, side-mount exterior elevation carriages (the manned turret "core" provided the traverse function), was meant for standardization on many late-war prototype developments of German heavy bomber airframes, but never came to fruition beyond a small number of dimensional prototype mockups and kinetic test units.The MG 131 fired electrically primed ammunition in order to sustain a high rate of fire when shooting through the propeller disc of a single-engined fighter. A pair of MG 131 machine guns was used as cowl armament on later models of the Bf 109G (which originally required one blister or Beule on each side of the fuselage, flanking the upper rear end of the engine, to house the larger breech of the new gun) and the Fw 190.Ouvrage L'Agaisen
Ouvrage L'Agaisen is a work (gros ouvrage) of the Maginot Line's Alpine extension, the Alpine Line, also known as the Little Maginot Line. The ouvrage consists of one entry block, two artillery blocks and one observation block above Sospel. Additional blocks were planned but not built. The ouvrage is located at an altitude of 663 metres (2,175 ft) on the Agaisen massif overlooking Sospel from the north. The position fired 1821 shots from Block 3's 75mm gun turret in 1940. It has an unusual 75mm gun turret in Block 3.
The ouvrage was built between 1930 and 1935, and was equipped from 1935 to 1937. L'Agaisen possesses an instruction casemate that was used to allow soldiers to practice attack and defense skills.SMS Leitha
SMS Leitha or Lajta Monitor Museumship was the first river monitor in Europe and the oldest and also the only remaining, fully restored warship of the Austro-Hungarian Navy.
The monitor was an innovation in the history of warship construction. The first European river monitors were constructed by the Austro-Hungarian Monarchy, namely the SMS Leitha and SMS Maros, and since then the river warships of the Monarchy were built in pairs. According to the customs of that time, river warships were named after the rivers of the Austro-Hungarian Empire. The names were chosen to reflect the dual (Imperial and Royal, Austrian and Hungarian) nature of the monarchy; thus, one of the ships received an Austrian name, the other one a Hungarian. This is the reason why this warship was named after the Austrian river Leitha (in Hungarian "Lajta"), while her sister ship was named after a Hungarian river, the Maros.
The construction of the first Danube monitors was dictated by the Monarchy's foreign policy ambitions, and the military and economic situation of the times. The ambition of becoming a great continental power, turned the attention of the Austro-Hungarian Monarchy in the direction of the Balkans as it could not expand towards the West. However, the Monarchy had to be prepared to compensate the states along the Danube, which had been newly liberated from Turkish rule, and that of Czarist Russia. To gain more influence in the Balkans therefore the commander of the Monarchy’s naval fleet, admiral Wilhelm von Tegetthoff suggested the construction of monitor type warships. Finances were raised, the necessary funds having been voted from the budget of 1869. The cost of the Leitha amounted to 425,000 forint.Tail gunner
A tail gunner or rear gunner is a crewman on a military aircraft who functions as a gunner defending against enemy fighter attacks from the rear, or "tail", of the plane. The tail gunner operates a flexible machine gun emplacement in the tail end of the aircraft with an unobstructed view toward the rear of the aircraft. While the term tail gunner is usually associated with a crewman inside a gun turret, the first tail guns were operated from open apertures within the aircraft's fuselage, like in the Scarff ring mechanism used in the British Handley Page V/1500 (a 1918 aircraft), and also, in the most evolved variants of this type of air-to-air anti-aircraft defense, they may also be operated by remote control from another part of the aircraft, like in the American B-52 bombers (an aircraft first introduced in 1955 but still in service).Tucker gun turret
The Tucker gun turret was a fast-traversing electrically powered gun turret widely described as having been mounted on World War II bombers and on some ground vehicles and small naval vessels like US Navy PT boats. American industrialist Preston Tucker first developed the turret for the experimental Tucker armored car in 1938.
Steve Lehto and Jay Leno, in their biography of Tucker, assert that it is a misconception that Tucker's turret was widely used on US bombers during the war. They assert that different manufacturers were each assigned contracts to develop different turrets for different planes, and that Tucker's firm was to build turrets for the Douglas B-18 Bolo. In the end no Tucker turrets equipped any bombers.
When Tucker was under investigation by the Security and Exchange Commission, a half-hour film entitled Tucker: The Man and his Car was prepared and shown to the Commission members. Lehto and Leno described the film's narrator "gushing" over Tucker and noted: "A short section on his wartime efforts to create the Tucker Combat Car introduced the Tucker Turret and may have been the source of the myth that his turrets were widely used during the war."
A Hollywood biopic of Tucker covered Tucker's production of the turret, prompting reviewers to characterize the turret design as "incredibly ergonomic, effective and convenient".Turret
In architecture, a turret (from Italian: torretta, little tower; Latin: turris, tower) is a small tower that projects vertically from the wall of a building such as a medieval castle. Turrets were used to provide a projecting defensive position allowing covering fire to the adjacent wall in the days of military fortification. As their military use faded, turrets were used for decorative purposes, as in the Scottish baronial style.
A turret can have a circular top with crenelations as seen in the picture at right, a pointed roof, or other kind of apex. It might contain a staircase if it projects higher than the building; however, a turret is not necessarily higher than the rest of the building; in this case, it is typically part of a room, that can be simply walked into – see the turret of Chateau de Chaumont on the collection of turrets, which also illustrates a turret on a modern skyscraper.
A building may have both towers and turrets; turrets might be smaller or higher but turrets instead project from the edge of a building rather than continue to the ground. The size of a turret is therefore limited, since it puts additional stresses on the structure of the building. Turrets were traditionally supported by a corbel.
In modern times, a gun turret is a weapon mount that houses the crew or mechanism of a projectile-firing weapon, allowing the weapon to be aimed and fired in some degree of azimuth and elevation. It can be found on warships, combat vehicles, military aircraft, and land fortifications, and usually offers some degree of armour or protection.Turret ship
Turret ships were a 19th-century type of warship, the earliest to have their guns mounted in a revolving gun turret, instead of a broadside arrangement.