Analog television

Analog television or analogue television is the original television technology that uses analog signals to transmit video and audio.[1] In an analog television broadcast, the brightness, colors and sound are represented by rapid variations of either the amplitude, frequency or phase of the signal.

Analog signals vary over a continuous range of possible values which means that electronic noise and interference becomes reproduced by the receiver. Thus with analog, a moderately weak signal becomes snowy and subject to interference. In contrast, a moderately weak digital signal and a very strong digital signal transmit equal picture quality. Analog television may be wireless (terrestrial television and satellite television) or can be distributed over a cable network using cable converters (cable television).

All broadcast television systems used analog signals before the arrival of digital television (DTV). Motivated by the lower bandwidth requirements of compressed digital signals, since the 2000s a digital television transition is proceeding in most countries of the world, with different deadlines for cessation of analog broadcasts.

OTVbelweder-front
Early Monochrome analog receiver with large dials for volume control and channel selection, and smaller ones for fine-tuning, brightness, contrast, and horizontal and vertical hold adjustments

Development

The earliest systems of analog television were mechanical television systems, which used spinning disks with patterns of holes punched into the disc to scan an image. A similar disk reconstructed the image at the receiver. Synchronization of the receiver disc rotation was handled through sync pulses broadcast with the image information. However these mechanical systems were slow, the images were dim and flickered severely, and the image resolution very low. Camera systems used similar spinning discs and required intensely bright illumination of the subject for the light detector to work.

Analog television did not really begin as an industry until the development of the cathode-ray tube (CRT), which uses a focused electron beam to trace lines across a phosphor coated surface. The electron beam could be swept across the screen much faster than any mechanical disc system, allowing for more closely spaced scan lines and much higher image resolution. Also far less maintenance was required of an all-electronic system compared to a spinning disc system. All-electronic systems became popular with households after the Second World War.

Standards

Broadcasters of analog television encode their signal using different systems. The official systems of transmission are named: A, B, C, D, E, F, G, H, I, K, K1, L, M and N. These systems determine the number of scan lines, frame rate, channel width, video bandwidth, video-audio separation, and so on.

The colors in those systems are encoded with one of three color coding schemes: NTSC, PAL, or SECAM,[2] and then use RF modulation to modulate this signal onto a very high frequency (VHF) or ultra high frequency (UHF) carrier. Each frame of a television image is composed of lines drawn on the screen. The lines are of varying brightness; the whole set of lines is drawn quickly enough that the human eye perceives it as one image. The next sequential frame is displayed, allowing the depiction of motion. The analog television signal contains timing and synchronization information, so that the receiver can reconstruct a two-dimensional moving image from a one-dimensional time-varying signal.

The first commercial television systems were black-and-white; the beginning of color television was in the 1950s.[3]

A practical television system needs to take luminance, chrominance (in a color system), synchronization (horizontal and vertical), and audio signals, and broadcast them over a radio transmission. The transmission system must include a means of television channel selection.

Analog broadcast television systems come in a variety of frame rates and resolutions. Further differences exist in the frequency and modulation of the audio carrier. The monochrome combinations still existing in the 1950s are standardized by the International Telecommunication Union (ITU) as capital letters A through N. When color television was introduced, the hue and saturation information was added to the monochrome signals in a way that black and white televisions ignore. In this way backwards compatibility was achieved. That concept is true for all analog television standards.

There were three standards for the way the additional color information can be encoded and transmitted. The first was the American NTSC (National Television Systems Committee) color television system. The European/Australian PAL (Phase Alternation Line rate) and the French-former Soviet Union SECAM (Séquentiel Couleur Avec Mémoire) standard were developed later and attempt to cure certain defects of the NTSC system. PAL's color encoding is similar to the NTSC systems. SECAM, though, uses a different modulation approach than PAL or NTSC.

In principle, all three color encoding systems can be combined with any scan line/frame rate combination. Therefore, in order to describe a given signal completely, it's necessary to quote the color system and the broadcast standard as a capital letter. For example, the United States, Canada, Mexico and South Korea use NTSC-M (many of these transitioned or transitioning to digital), Japan uses NTSC-J (discontinued in 2012, when Japan transitioned to digital (ISDB)), the UK uses PAL-I (discontinued in 2012, when UK transitioned to digital (DVB-T)), France uses SECAM-L (discontinued in 2011, when France transitioned to digital (DVB-T)), much of Western Europe and Australia use PAL-B/G (Many of these transitioned or transitioning to DVB-T as digital television standards), most of Eastern Europe uses SECAM-D/K or PAL-D/K and so on.

However, not all of these possible combinations actually exist. NTSC is currently only used with system M, even though there were experiments with NTSC-A (405 line) in the UK and NTSC-N (625 line) in part of South America. PAL is used with a variety of 625-line standards (B,G,D,K,I,N) but also with the North American 525-line standard, accordingly named PAL-M. Likewise, SECAM is used with a variety of 625-line standards.

For this reason many people refer to any 625/25 type signal as "PAL" and to any 525/30 signal as "NTSC", even when referring to digital signals; for example, on DVD-Video, which does not contain any analog color encoding, and thus no PAL or NTSC signals at all. Even though this usage is common, it is misleading, as that is not the original meaning of the terms PAL/SECAM/NTSC.

Although a number of different broadcast television systems were in use worldwide, the same principles of operation apply.[4]

In many countries, over-the-air broadcast television of analog audio and analog video signals has been discontinued, to allow the re-use of the television broadcast radio spectrum for other services such as datacasting and subchannels.

Displaying an image

A cathode-ray tube (CRT) television displays an image by scanning a beam of electrons across the screen in a pattern of horizontal lines known as a raster. At the end of each line the beam returns to the start of the next line; the end of the last line is a link that returns to the top of the screen. As it passes each point the intensity of the beam is varied, varying the luminance of that point. A color television system is identical except that an additional signal known as chrominance controls the color of the spot.

Raster scanning is shown in a slightly simplified form below.

Raster-scan

When analog television was developed, no affordable technology for storing any video signals existed; the luminance signal has to be generated and transmitted at the same time at which it is displayed on the CRT. It is therefore essential to keep the raster scanning in the camera (or other device for producing the signal) in exact synchronization with the scanning in the television.

The physics of the CRT require that a finite time interval be allowed for the spot to move back to the start of the next line (horizontal retrace) or the start of the screen (vertical retrace). The timing of the luminance signal must allow for this.

TV screen close-up
Close up image of analog color screen

The human eye has a characteristic called Phi phenomenon. Quickly displaying successive scan images will allow the apparent illusion of smooth motion. Flickering of the image can be partially solved using a long persistence phosphor coating on the CRT, so that successive images fade slowly. However, slow phosphor has the negative side-effect of causing image smearing and blurring when there is a large amount of rapid on-screen motion occurring.

The maximum frame rate depends on the bandwidth of the electronics and the transmission system, and the number of horizontal scan lines in the image. A frame rate of 25 or 30 hertz is a satisfactory compromise, while the process of interlacing two video fields of the picture per frame is used to build the image. This process doubles the apparent number of video frames per second and further reduces flicker and other defects in transmission.

Other types of display screens

Plasma screens and LCD screens have been used in analog television sets. These types of display screens use lower voltages than older CRT displays. Many dual system television receivers, equipped to receive both analog transmissions and digital transmissions have analog tuner receiving capability and must use a television antenna.

Receiving signals

The television system for each country will specify a number of television channels within the UHF or VHF frequency ranges. A channel actually consists of two signals: the picture information is transmitted using amplitude modulation on one frequency, and the sound is transmitted with frequency modulation at a frequency at a fixed offset (typically 4.5 to 6 MHz) from the picture signal.

The channel frequencies chosen represent a compromise between allowing enough bandwidth for video (and hence satisfactory picture resolution), and allowing enough channels to be packed into the available frequency band. In practice a technique called vestigial sideband is used to reduce the channel spacing, which would be nearly twice the video bandwidth if pure AM was used.

Signal reception is invariably done via a superheterodyne receiver: the first stage is a tuner which selects a television channel and frequency-shifts it to a fixed intermediate frequency (IF). The signal amplifier performs amplification to the IF stages from the microvolt range to fractions of a volt.

Extracting the sound

At this point the IF signal consists of a video carrier signal at one frequency and the sound carrier at a fixed offset. A demodulator recovers the video signal. Also at the output of the same demodulator is a new frequency modulated sound carrier at the offset frequency. In some sets made before 1948, this was filtered out, and the sound IF of about 22 MHz was sent to an FM demodulator to recover the basic sound signal. In newer sets, this new carrier at the offset frequency was allowed to remain as intercarrier sound, and it was sent to an FM demodulator to recover the basic sound signal. One particular advantage of intercarrier sound is that when the front panel fine tuning knob is adjusted, the sound carrier frequency does not change with the tuning, but stays at the above-mentioned offset frequency. Consequently, it is easier to tune the picture without losing the sound.

So the FM sound carrier is then demodulated, amplified, and used to drive a loudspeaker. Until the advent of the NICAM and MTS systems, television sound transmissions were invariably monophonic.

Structure of a video signal

The video carrier is demodulated to give a composite video signal; this contains luminance, chrominance and synchronization signals;[5] this is identical to the video signal format used by analog video devices such as VCRs or CCTV cameras. Note that the RF signal modulation is inverted compared to the conventional AM: the minimum video signal level corresponds to maximum carrier amplitude, and vice versa. To ensure good linearity (fidelity), consistent with affordable manufacturing costs of transmitters and receivers, the video carrier is never shut off altogether. When intercarrier sound was invented later in 1948, not completely shutting off the carrier had the side effect of allowing intercarrier sound to be economically implemented.

Video-line

Each line of the displayed image is transmitted using a signal as shown above. The same basic format (with minor differences mainly related to timing and the encoding of color) is used for PAL, NTSC and SECAM television systems. A monochrome signal is identical to a color one, with the exception that the elements shown in color in the diagram (the color burst, and the chrominance signal) are not present.

Videosignal porch
Portion of a PAL video signal. From left to right: end of a video scan line, front porch, horizontal sync pulse, back porch with color burst, and beginning of next line

The front porch is a brief (about 1.5 microsecond) period inserted between the end of each transmitted line of picture and the leading edge of the next line sync pulse. Its purpose was to allow voltage levels to stabilise in older televisions, preventing interference between picture lines. The front porch is the first component of the horizontal blanking interval which also contains the horizontal sync pulse and the back porch.[6][7]

The back porch is the portion of each scan line between the end (rising edge) of the horizontal sync pulse and the start of active video. It is used to restore the black level (300 mV) reference in analog video. In signal processing terms, it compensates for the fall time and settling time following the sync pulse.[6][7]

In color television systems such as PAL and NTSC, this period also includes the colorburst signal. In the SECAM system it contains the reference subcarrier for each consecutive color difference signal in order to set the zero-color reference.

In some professional systems, particularly satellite links between locations, the audio is embedded within the back porch of the video signal, to save the cost of renting a second channel.

Monochrome video signal extraction

The luminance component of a composite video signal varies between 0 V and approximately 0.7 V above the "black" level. In the NTSC system, there is a blanking signal level used during the front porch and back porch, and a black signal level 75 mV above it; in PAL and SECAM these are identical.

In a monochrome receiver the luminance signal is amplified to drive the control grid in the electron gun of the CRT. This changes the intensity of the electron beam and therefore the brightness of the spot being scanned. Brightness and contrast controls determine the DC shift and amplification, respectively.

Color video signal extraction

Burnt-in timecode
Color bar generator test signal

A color signal conveys picture information for each of the red, green, and blue components of an image (see the article on color space for more information). However, these are not simply transmitted as three separate signals, because: such a signal would not be compatible with monochrome receivers (an important consideration when color broadcasting was first introduced). It would also occupy three times the bandwidth of existing television, requiring a decrease in the number of television channels available. Furthermore, typical problems with signal transmission (such as differing received signal levels between different colors) would produce unpleasant side effects.

Instead, the RGB signals are converted into YUV form, where the Y signal represents the lightness and darkness (luminance) of the colors in the image. Because the rendering of colors in this way is the goal of both black and white (monochrome) film and black and white (monochrome) television systems, the Y signal is ideal for transmission as the luminance signal. This ensures a monochrome receiver will display a correct picture in black and white, where a given color is reproduced by a shade of gray that correctly reflects how light or dark the original color is.

The U and V signals are "color difference" signals. The U signal is the difference between the B signal and the Y signal, also known as B minus Y (B-Y), and the V signal is the difference between the R signal and the Y signal, also known as R minus Y (R-Y). The U signal then represents how "purplish-blue" or its complementary color "yellowish-green" the color is, and the V signal how "purplish-red" or its complementary "greenish-cyan" it is. The advantage of this scheme is that the U and V signals are zero when the picture has no color content. Since the human eye is more sensitive to errors in luminance than in color, the U and V signals can be transmitted in a relatively lossy (specifically: bandwidth-limited) way with acceptable results.

In the receiver, a single demodulator can extract an additive combination of U plus V. An example is the X demodulator used in the X/Z demodulation system. In that same system, a second demodulator, the Z demodulator, also extracts an additive combination of U plus V, but in a different ratio. The X and Z color difference signals are further matrixed into three color difference signals, (R-Y), (B-Y), and (G-Y). The combinations of usually two, but sometimes three demodulators were:

  1. (I) / (Q), (as used in the 1954 RCA CTC-2 and the 1985 RCA "Colortrak" series, and the 1954 Arvin, and some professional color monitors in the 1990s),
  2. (R-Y) / (Q), as used in the 1955 RCA 21 inch color receiver,
  3. (R-Y) / (B-Y), used in the first color receiver on the market (Westinghouse, not RCA),
  4. (R-Y) / (G-Y), (as used in the RCA Victor CTC-4 chassis),
  5. (R-Y) / (B-Y) / (G-Y),
  6. (X) / (Z), as used in many receivers of the late '50s and throughout the '60s.

In the end, further matrixing of the above color-difference signals c through f yielded the three color-difference signals, (R-Y), (B-Y), and (G-Y).

The R,G,B signals in the receiver needed for the display device (CRT, Plasma display or LCD display) are electronically derived by matrixing as follows: R is the additive combination of (R-Y) with Y, G is the additive combination of (G-Y) with Y, and B is the additive combination of (B-Y) with Y. All of this is accomplished electronically. It can be seen that in the combining process, the low resolution portion of the Y signals cancel out, leaving R,G, and B signals able to render a low-resolution image in full color. However, the higher resolution portions of the Y signals do not cancel out, and so are equally present in R, G, and B, producing the higher definition (higher resolution) image detail in monochrome, although it appears to the human eye as a full-color and full resolution picture.

Waveform monitor
Color signals mixed with video signal (two horizontal lines in sequence)

In the NTSC and PAL color systems, U and V are transmitted by using quadrature amplitude modulation of a subcarrier. This kind of modulation applies two independent signals to one subcarrier, with the idea that both signals will be recovered independently at the receive end. Before transmission, the subcarrier itself, is removed from the active (visible) portion of the video, and moved, in the form of a burst, to the horizontal blanking portion, which is not directly visible on screen. (More about the burst below.)

For NTSC, the subcarrier is a 3.58 MHz sine wave. For the PAL system it is a 4.43 MHz sine wave. After the above-mentioned quadrature amplitude modulation of the subcarrier, subcarrier sidebands are produced, and the subcarrier itself is filtered out of the visible portion of the video, since it is the subcarrier sidebands that carry all of the U and V information, and the subcarrier itself carries no information.

The resulting subcarrier sidebands is also known as "chroma" or "chrominance". Physically, this chrominance signal is a 3.58 MHz(NTSC) or 4.43 MHz(PAL) sine wave which, in response to changing U and V values, changes phase as compared to the subcarrier, and also changes amplitude.

As it turns out, the chroma amplitude (when considered together with the Y signal) represents the approximate saturation of a color, and the chroma phase against the subcarrier as reference, approximately represents the hue of the color. For particular test colors found in the test color bar pattern, exact amplitudes and phases are sometimes defined for test and trouble shooting purposes only.

Although, in response to changing U and V values, the chroma sinewave changes phase with respect to the subcarrier, it's not correct to say that the subcarrier is simply "phase modulated". That is because a single sine wave U test signal with QAM produces only one pair of sidebands, whereas real phase modulation under the same test conditions would produce multiple sets of sidebands occupying more frequency spectrum.

In NTSC, the chrominance sine wave has the same average frequency as the subcarrier frequency. But a spectrum analyzer instrument shows that, for transmitted chrominance, the frequency component at the subcarrier frequency is actually zero energy, verifying that the subcarrier was indeed removed before transmission.

These sideband frequencies are within the luminance signal band, which is why they are called "subcarrier" sidebands instead of simply "carrier" sidebands. Their exact frequencies were chosen such that (for NTSC), they are midway between two harmonics of the frame repetition rate, thus ensuring that the majority of the power of the luminance signal does not overlap with the power of the chrominance signal.

In the British PAL (D) system, the actual chrominance center frequency, with equal lower and upper sidebands, is 4.43361875 MHz, a direct multiple of the scan rate frequency. This frequency was chosen to minimize the chrominance beat interference pattern that would be visible in areas of high color saturation in the transmitted picture.

At certain times, the chrominance signal represents only the U signal, and 70 nanoseconds (NTSC) later, the chrominance signal represents only the V signal. (This is the nature of the quadrature amplitude modulation process that created the chrominance signal.) About 70 nanoseconds later still, -U, and another 70 nanoseconds, -V.

So to extract U, a synchronous demodulator is utilized, which uses the subcarrier to briefly gate (sample) the chroma every 280 nanoseconds, so that the output is only a train of discrete pulses, each having an amplitude that is the same as the original U signal at the corresponding time. In effect, these pulses are discrete-time analog samples of the U signal. The pulses are then low-pass filtered so that the original analog continuous-time U signal is recovered. For V, a 90 degree shifted subcarrier briefly gates the chroma signal every 280 nanoseconds, and the rest of the process is identical to that used for the U signal.

Gating at any other time than those times mentioned above will yield an additive mixture of any two of U, V, -U, or -V. One of these "off-axis" (that is, off the U and V axis) gating methods is called I/Q demodulation. Another much more popular "off-axis" scheme was the X/Z demodulation system. Further matrixing recovered the original U and V signals. This scheme was actually the most popular demodulator scheme throughout the 60's.

The above process uses the subcarrier. But as previously mentioned, it was deleted before transmission, and only the chroma is transmitted. Therefore, the receiver must reconstitute the subcarrier. For this purpose, a short burst of subcarrier, known as the color burst, is transmitted during the back porch (re-trace blanking period) of each scan line. A subcarrier oscillator in the receiver locks onto this signal (see phase-locked loop) to achieve a phase reference, resulting in the oscillator producing the reconstituted subcarrier.

(A second use of the burst in more expensive or newer receiver models is a reference to an AGC system to compensate for chroma gain imperfections in reception.)

Hanoverbars without PAL delay
Test card showing "Hanover bars" (color banding phase effect) in Pal S (simple) signal mode of transmission.

NTSC uses this process unmodified. Unfortunately, this often results in poor color reproduction due to phase errors in the received signal, caused sometimes by multipath, but mostly by poor implementation at the studio end. With the advent of solid state receivers, cable TV, and digital studio equipment for conversion to an over-the-air analog signal, these NTSC problems have been largely fixed, leaving operator error at the studio end as the sole color rendition weakness of the NTSC system. In any case, the PAL D (delay) system mostly corrects these kind of errors by reversing the phase of the signal on each successive line, and the averaging the results over pairs of lines. This process is achieved by the use of a 1H (where H = horizontal scan frequency) duration delay line. (A typical circuit used with this device converts the low frequency color signal to ultrasound and back again). Phase shift errors between successive lines are therefore cancelled out and the wanted signal amplitude is increased when the two in-phase (coincident) signals are re-combined.

NTSC is more spectrum efficient than PAL, giving more picture detail for a given bandwidth. This is because sophisticated comb filters in receivers are more effective with NTSC's 4 field color phase cadence compared to PAL's 8 field cadence. However, in the end, the larger channel width of most PAL systems in Europe still give their PAL systems the edge in transmitting more picture detail.

In the SECAM television system, U and V are transmitted on alternate lines, using simple frequency modulation of two different color subcarriers.

In some analog color CRT displays, starting in 1956, the brightness control signal (luminance) is fed to the cathode connections of the electron guns, and the color difference signals (chrominance signals) are fed to the control grids connections. This simple CRT matrix mixing technique was replaced in later solid state designs of signal processing with the original matrixing method used in the 1954 and 1955 color TV receivers.

Synchronization

Synchronizing pulses added to the video signal at the end of every scan line and video frame ensure that the sweep oscillators in the receiver remain locked in step with the transmitted signal, so that the image can be reconstructed on the receiver screen.[6][7][8]

A sync separator circuit detects the sync voltage levels and sorts the pulses into horizontal and vertical sync. (see section below – Other technical information, for extra detail.)

Horizontal synchronization

The horizontal synchronization pulse (horizontal sync, or HSync), separates the scan lines. The horizontal sync signal is a single short pulse which indicates the start of every line. The rest of the scan line follows, with the signal ranging from 0.3 V (black) to 1 V (white), until the next horizontal or vertical synchronization pulse.

The format of the horizontal sync pulse varies. In the 525-line NTSC system it is a 4.85 µs-long pulse at 0 V. In the 625-line PAL system the pulse is 4.7 µs synchronization pulse at 0 V . This is lower than the amplitude of any video signal (blacker than black) so it can be detected by the level-sensitive "sync stripper" circuit of the receiver.

Vertical synchronization

Vertical synchronization (also called vertical sync or VSync) separates the video fields. In PAL and NTSC, the vertical sync pulse occurs within the vertical blanking interval. The vertical sync pulses are made by prolonging the length of HSYNC pulses through almost the entire length of the scan line.

The vertical sync signal is a series of much longer pulses, indicating the start of a new field. The sync pulses occupy the whole of line interval of a number of lines at the beginning and end of a scan; no picture information is transmitted during vertical retrace. The pulse sequence is designed to allow horizontal sync to continue during vertical retrace; it also indicates whether each field represents even or odd lines in interlaced systems (depending on whether it begins at the start of a horizontal line, or midway through).

The format of such a signal in 525-line NTSC is:

  • pre-equalizing pulses (6 to start scanning odd lines, 5 to start scanning even lines)
  • long-sync pulses (5 pulses)
  • post-equalizing pulses (5 to start scanning odd lines, 4 to start scanning even lines)

Each pre- or post- equalizing pulse consists in half a scan line of black signal: 2 µs at 0 V, followed by 30 µs at 0.3 V.

Each long sync pulse consists in an equalizing pulse with timings inverted: 30 µs at 0 V, followed by 2 µs at 0.3 V.

In video production and computer graphics, changes to the image are often kept in step with the vertical synchronization pulse to avoid visible discontinuity of the image. Since the frame buffer of a computer graphics display imitates the dynamics of a cathode-ray display, if it is updated with a new image while the image is being transmitted to the display, the display shows a mishmash of both frames, producing a page tearing artifact partway down the image.

Vertical synchronization eliminates this by timing frame buffer fills to coincide with the vertical blanking interval, thus ensuring that only whole frames are seen on-screen. Software such as video games and computer-aided design (CAD) packages often allow vertical synchronization as an option, because it delays the image update until the vertical blanking interval. This produces a small penalty in latency, because the program has to wait until the video controller has finished transmitting the image to the display before continuing. Triple buffering reduces this latency significantly.

Two timing intervals are defined – the front porch between the end of displayed video and the start of the sync pulse, and the back porch after the sync pulse and before displayed video. These and the sync pulse itself are called the horizontal blanking (or retrace) interval and represent the time that the electron beam in the CRT is returning to the start of the next display line.

Horizontal Hold and Vertical Hold

Analog television receivers and composite monitors often provide manual controls to adjust horizontal and vertical timing.

The sweep (or deflection) oscillators were designed to run without a signal from the television station (or VCR, computer, or other composite video source). This provides a blank canvas, similar to today's "CHECK SIGNAL CABLE" messages on monitors: it allows the television receiver to display a raster to confirm basic operation of the set's most fundamental circuits, and to allow an image to be presented during antenna placement. With sufficient signal strength, the receiver's sync separator circuit would split timebase pulses from the incoming video and use them to reset the horizontal and vertical oscillators at the appropriate time to synchronize with the signal from the station.

The free-running oscillation of the horizontal circuit is especially critical, as the horizontal deflection circuits typically power the flyback transformer (which provides acceleration potential for the CRT) as well as the filaments for the high voltage rectifier tube and sometimes the filament(s) of the CRT itself. Without the operation of the horizontal oscillator and output stages, for virtually every analog television receiver since the 1940s, there will be absolutely no illumination of the CRT's face.

The lack of precision timing components in early television receivers meant that the timebase circuits occasionally needed manual adjustment. If their free-run frequencies were too far from the actual line and field rates, the circuits would not be able to follow the incoming sync signals. Loss of horizontal synchronization usually resulted in an unwatchable picture; loss of vertical synchronization would produce an image rolling up or down the screen.

The adjustment took the form of horizontal hold and vertical hold controls, usually on the front panel along with other common controls. These adjusted the free-run frequencies of the corresponding timebase oscillators.

Properly working, adjusting a horizontal or vertical hold should cause the picture to almost "snap" into place on the screen; this is called sync lock. A slowly rolling vertical picture demonstrates that the vertical oscillator is nearly synchronized with the television station but is not locking to it, often due to a weak signal or a failure in the sync separator stage not resetting the oscillator. Sometimes, the black interval bar will almost stop at the right place, again indicating a fault in sync separation is not properly resetting the vertical oscillator.

Horizontal sync errors cause the image to be torn diagonally and repeated across the screen as if it were wrapped around a screw or a barber's pole; the greater the error, the more "copies" of the image will be seen at once wrapped around the barber pole. Given the importance of the horizontal sync circuit as a power supply to many subcircuits in the receiver, they may begin to malfunction as well; and horizontal output components which were designed to work together in a resonant circuit may become damaged.

In the earliest electronic television receivers (1930s-1950s), the timebase for the sweep oscillators was generally derived from RC circuits based on carbon resistors and paper capacitors. After turning on the receiver, the vacuum tubes in the set would warm up and the oscillators would begin to run, allowing a watchable picture. Resistors were generally simple pieces of carbon inside a Bakelite enclosure, and the capacitors were usually alternating layers of paper and aluminum foil inside cardboard tubes sealed with bee's wax. Moisture ingress (from ambient air humidity) as well as thermal instability of these components affected their electrical values. As the heat from the tubes and the electrical currents passing through the RC circuits warmed them up, the electrical properties of the RC timebase would shift, causing the oscillators to drift in frequency to a point that they could no longer be synchronized with the received pulses coming from the TV station via the sync separator circuit, causing tearing (horizontal) or rolling (vertical).

Hermetically-sealed passive components and cooler-running semiconductors as active components gradually improved reliability to the point where the horizontal hold was moved to the rear of the set first, and the vertical hold control (due to the longer period in the RC constant) persisted as a front panel control well into the 1970s as the consistency of larger-value capacitors increased.

By the early 1980s the efficacy of the synchronization circuits, plus the inherent stability of the sets' oscillators, had been improved to the point where these controls were no longer necessary. Integrated Circuits which eliminated the horizontal hold control were starting to appear as early as 1969[9].

The final generations of analog television receivers (most TV sets with internal on-screen displays to adjust brightness, color, tint, contrast) used "TV-set-on-a-chip" designs where the receiver's timebases were divided down from crystal oscillators, usually based on the 3.58MHz NTSC colorburst reference. PAL and SECAM receivers were similar though operating at different frequencies. With these sets, adjustment of the free-running frequency of either sweep oscillator was either physically impossible (being derived inside the integrated circuit) or possibly through a hidden service mode typically offering only NTSC/PAL frequency switching, accessible through the On-Screen Display's menu system.

Horizontal and Vertical Hold controls were rarely used in CRT-based computer monitors, as the quality and consistency of components were quite high by the advent of the computer age, but might be found on some composite monitors used with 1970s-1980s home or personal computers.

There is no equivalent in modern television systems.

Other technical information

Components of a television system

A typical analog monochrome television receiver is based around the block diagram shown below:

TV-block-diagram

The tuner is the object which "plucks" the television signals out of the air, with the aid of an antenna. There are two types of tuners in analog television, VHF and UHF tuners. The VHF tuner selects the VHF television frequency. This consists of a 4MHz video bandwidth and a 2MHz audio bandwidth. It then amplifies the signal and converts it to a 45.75MHz Intermediate Frequency (IF) amplitude-modulated picture and a 41.25MHz IF frequency-modulated audio carrier.

The IF amplifiers are centered @ 44MHz for optimal frequency transference of the audio and frequency carriers. What centers this frequency is the IF transformer. They are designed for for a certain amount of bandwidth to encompass the audio and video. It depends on the amount of stages (the amplifier between the transformers). Most of the early television sets (1939-45) used 4 stages with specially designed video amplifier tubes (the type 1852/6AC7). In 1946 the RCA presented a new innovation in television; the RCA 630TS. Instead of using the 1852 octal tube, it use the 6AG5 7-pin miniature tube. It still had 4 stages, but it was 1/2 the size. Soon all of the manufactures followed RCA and designed better IF stages. They developed higher amplification tubes, and lower stage counts with more amplification. When the tube era came to an end in the mid-70s, they had shrunk the IF stages down to 1-2 (depending on the set) and with a same amplification as the 4 stage, 1852 tube sets. Like radio, television has Automatic Gain Control (AGC). This controls the gain of the IF amplifier stages and the tuner. More of this will be discussed below.

The video amp and output amplifier consists of a low linear pentode or a high powered transistor. The video amp and output stage does more than just do what is in your name. It separates the 45.75MHz from the 41.25MHz. It simply uses a diode to detect the video signal. But the frequency modulated audio is still in the video. Since the diode only detects AM signals, the FM audio signal is still in the video in the form of a 4.5MHz signal. There are two ways to attach this problem, and both of them work. We can detect the signal before it enters into the video amplifier, or do it after the audio amplifier. Many television sets (1946 to late 1960s) used the after video amplification method, but of course there is the occasional exception. Many of the later set late (1960s-now) use the before-the-video amplifier way. In some of the early television sets (1939-45) used its own separate tuner, so there was no need for a detection stage next to the amplifier. After the video detector, the video is amplified and sent to the sync separator and then to the picture tube.

At this point, we will now look at the audio section. The means of detection of the audio signal is by a 4.5MHz trap coil/transformer. After that, it then goes to a 4.5MHz amplifier. This amplifier prepares the signal for the 4.5Mhz detector. It then goes through a 4.5MHz IF transformer to the detector. In television, there are 2 ways of detecting FM signals. One way is by the ratio detector. This is simple, but very hard to align. The next is a relatively simple detector. This is the quadrature detector. It was invent in 1954. The first tube designed for this purpose was the 6BN6 type. It is easy to align and simple in circuitry. It was such a good design that is is still being used today in Integrated circuit form. After the detector, it goes to audio amplifier.

The next part is the sync separator/clipper. This also does more than what is in its name. It also forms the AGC voltage, as previously stated. This sync separator turns the video into a signal that the Horizontal and Vertical oscillators can use to keep in sync with the video.

The horizontal and vertical oscillators form the raster on the CRT. They are kept in sync by the sync separator. There are many ways to create these oscillators. The first one is the earliest of its kind is the thyratron oscillator. Although it is known to drift, it makes a perfect sawtooth wave. This sawtooth wave is so good that no linearity control is needed. This oscillator was for the electrostatic deflection CRTs. It found some purpose for the electromagnetically deflected CRTs. The next oscillator is the blocking oscillator. It uses a transformer to create a sawtooth wave. This was only used for a brief time period and never was very popular after the beginning. The next oscillator is the multvibrator. This oscillator was probably the most successful. It needed more adjustment than the other oscillators, but it is very simple and effective. This oscillator was so popular that it was used from the early 1950s till today.

The oscillator amplifier is sorted into two categories. The vertical amplifier directly drives the yoke. There is not much to the this. It is similar to audio amplifier. The horizontal oscillator is a different situation. The oscillator must supply the high voltage and the yoke power. This requires a high power flyback transformer, and a high powered tube or transistor. This is a problematic section for CRT televisions because it has to handle high power.

Sync separator

Videosignal porch
Portion of a PAL videosignal. From left to right: end of a video line, front porch, horizontal sync pulse, back porch with color burst, and beginning of next line
Videosignal vsync
Beginning of the frame, showing several scan lines; the terminal part of the vertical sync pulse is at the left
Videosignal frame
PAL videosignal frames. Left to right: frame with scan lines (overlapping together, horizontal sync pulses show as the doubled straight horizontal lines), vertical blanking interval with vertical sync (shows as brightness increase of the bottom part of the signal in almost the leftmost part of the vertical blanking interval), entire frame, another VBI with VSYNC, beginning of third frame

Image synchronization is achieved by transmitting negative-going pulses; in a composite video signal of 1 volt amplitude, these are approximately 0.3 V below the "black level". The horizontal sync signal is a single short pulse which indicates the start of every line. Two timing intervals are defined – the front porch between the end of displayed video and the start of the sync pulse, and the back porch after the sync pulse and before displayed video. These and the sync pulse itself are called the horizontal blanking (or retrace) interval and represent the time that the electron beam in the CRT is returning to the start of the next display line.

The vertical sync signal is a series of much longer pulses, indicating the start of a new field. The sync pulses occupy the whole of line interval of a number of lines at the beginning and end of a scan; no picture information is transmitted during vertical retrace. The pulse sequence is designed to allow horizontal sync to continue during vertical retrace; it also indicates whether each field represents even or odd lines in interlaced systems (depending on whether it begins at the start of a horizontal line, or midway through).

In the television receiver, a sync separator circuit detects the sync voltage levels and sorts the pulses into horizontal and vertical sync.

Loss of horizontal synchronization usually resulted in an unwatchable picture; loss of vertical synchronization would produce an image rolling up or down the screen.

Counting sync pulses, a video line selector picks a selected line from a TV signal, used for teletext, on-screen displays, station identification logos as well as in the industry when cameras were used as a sensor.

Timebase circuits

In an analog receiver with a CRT display sync pulses are fed to horizontal and vertical timebase circuits (commonly called "sweep circuits" in the United States), each consisting of an oscillator and an amplifier. These generate modified sawtooth and parabola current waveforms to scan the electron beam in a linear way. The waveform shapes are necessary to make up for the distance variations from the electron beam source and the screen surface. The oscillators are designed to free-run at frequencies very close to the field and line rates, but the sync pulses cause them to reset at the beginning of each scan line or field, resulting in the necessary synchronization of the beam sweep with the originating signal. The output waveforms from the timebase amplifiers are fed to the horizontal and vertical deflection coils wrapped around the CRT tube. These coils produce magnetic fields proportional to the changing current, and these deflect the electron beam across the screen.

In the 1950s, the power for these circuits was derived directly from the mains supply. A simple circuit consisted of a series voltage dropper resistance and a rectifier valve (tube) or semiconductor diode. This avoided the cost of a large high voltage mains supply (50 or 60 Hz) transformer. This type of circuit was used for thermionic valve (vacuum tube) technology. It was inefficient and produced a lot of heat which led to premature failures in the circuitry. Although failure were common, it was easily repairable.

In the 1960s, semiconductor technology was introduced into timebase circuits. During the late 1960s in the UK, synchronous (with the scan line rate) power generation was introduced into solid state receiver designs.[10] These had very complex circuits in which faults were difficult to trace, but had very efficient use of power.

In the early 1970s AC mains (50 or 60 Hz), and line timebase (15,625 Hz), thyristor based switching circuits were introduced. In the UK use of the simple (50 Hz) types of power circuits were discontinued. The reason for design changes arose from the electricity supply contamination problems arising from EMI,[11] and supply loading issues due to energy being taken from only the positive half cycle of the mains supply waveform.[12]

CRT flyback power supply

Most of the receiver's circuitry (at least in transistor- or IC-based designs) operates from a comparatively low-voltage DC power supply. However, the anode connection for a cathode-ray tube requires a very high voltage (typically 10–30 kV) for correct operation.

This voltage is not directly produced by the main power supply circuitry; instead the receiver makes use of the circuitry used for horizontal scanning. Direct current (DC), is switched though the line output transformer, and alternating current (AC) is induced into the scan coils. At the end of each horizontal scan line the magnetic field, which has built up in both transformer and scan coils by the current, is a source of latent electromagnetic energy. This stored collapsing magnetic field energy can be captured. The reverse flow, short duration, (about 10% of the line scan time) current from both the line output transformer and the horizontal scan coil is discharged again into the primary winding of the flyback transformer by the use of a rectifier which blocks this negative reverse emf. A small value capacitor is connected across the scan switching device. This tunes the circuit inductances to resonate at a much higher frequency. This slows down (lengthens) the flyback time from the extremely rapid decay rate that would result if they were electrically isolated during this short period. One of the secondary windings on the flyback transformer then feeds this brief high voltage pulse to a Cockcroft–Walton generator design voltage multiplier. This produces the required EHT supply. A flyback converter is a power supply circuit operating on similar principles.

A typical modern design incorporates the flyback transformer and rectifier circuitry into a single unit with a captive output lead, (known as a diode split line output transformer or an Integrated High Voltage Transformer (IHVT)),[13] so that all high-voltage parts are enclosed. Earlier designs used a separate line output transformer and a well insulated high voltage multiplier unit. The high frequency (15 kHz or so) of the horizontal scanning allows reasonably small components to be used.

Transition to digital

The first country to make a wholesale switch to digital over-the-air (terrestrial television) broadcasting was Luxembourg in 2006, followed later in 2006 by the Netherlands; in 2007 by Finland, Andorra, Sweden and Switzerland; in 2008 by Belgium (Flanders) and Germany; in 2009 by the United States (high power stations), southern Canada, the Isle of Man, Norway, and Denmark. In 2010, Belgium (Wallonia), Spain, Wales, Latvia, Estonia, the Channel Islands, San Marino, Croatia and Slovenia; in 2011 Israel, Austria, Monaco, Cyprus, Japan (excluding Miyagi, Iwate, and Fukushima prefectures), Malta and France; in 2012 the Czech Republic, Arab World, Taiwan, Portugal, Japan (including Miyagi, Iwate, and Fukushima prefectures), Serbia, Italy, Canada, Mauritius, the United Kingdom, the Republic of Ireland, Lithuania, Slovakia, Gibraltar, and South Korea; in 2013, the Republic of Macedonia, Poland, Bulgaria, Hungary, Australia, and New Zealand, completed the transition. The United Kingdom made the transition to digital television between 2008 and 2012, with the exception of Barrow-in-Furness, which made the switch over in 2007. The first digital TV-only area in the United Kingdom was Ferryside in Carmarthenshire.

The Digital television transition in the United States for high-powered transmission was completed on 12 June 2009, the date that the Federal Communications Commission (FCC) set. Almost two million households could no longer watch television because they had not prepared for the transition. The switchover had been delayed by the DTV Delay Act.[14] While the majority of the viewers of over-the-air broadcast television in the U.S. watch full-power stations (which number about 1800), there are three other categories of television stations in the U.S.: low-power broadcasting stations, class A stations, and television translator stations. They were given later deadlines. In broadcasting, whatever happens in the United States also influences southern Canada and northern Mexico because those areas are covered by television stations in the U.S.

In Japan, the switch to digital began in northeastern Ishikawa Prefecture on 24 July 2010 and ended in 43 of the country's 47 prefectures (including the rest of Ishikawa) on 24 July 2011, but in Fukushima, Iwate, and Miyagi prefectures, the conversion was delayed to 31 March 2012, due to complications from the 2011 Tōhoku earthquake and tsunami and its related nuclear accidents.

In Canada, most of the larger cities turned off analog broadcasts on 31 August 2011.[15]

China is scheduled to end analog broadcasting between 2015 and 2018, due to the large size of the country.

Brazil switched to digital television on 2 December 2007 in its major cities. It is now estimated that Brazil will end analog broadcasting in 2023.

In Malaysia, the Malaysian Communications & Multimedia Commission (MCMC) advertised for tender bids to be submitted in the third quarter of 2009 for the 470 through 742 MHz UHF allocation, to enable Malaysia's broadcast system to move into DTV. The new broadcast band allocation would result in Malaysia's having to build an infrastructure for all broadcasters, using a single digital terrestrial transmission/television broadcast (DTTB) channel. Large portions of Malaysia are covered by television broadcasts from Singapore, Thailand, Brunei, and Indonesia (from Borneo and Batam).

In Singapore, digital television under DVB-T2 began on 16 December 2013. The switchover has been delayed many times until 31 December 2018.

In the Philippines, the National Telecommunications Commission required all broadcasting companies to end analog broadcasting on December 31, 2015 at 11:59 p.m. Due to delay of the release of the implementing rules and regulations for digital television broadcast, the target date was moved to 2020. Full digital broadcast is expected in 2021 and all of the analog TV services should be shut down by the end of 2023.

In the Russian Federation, the RTRS full disabled analog broadcasting in 3 June 2019[16], excluding capital city (Moscow, is a test region) where it happens 15 April same year[17].

See also

References

  1. ^ "Television Technical Performance Code" (PDF). Ofcom – office of Communications. December 2006. Archived (PDF) from the original on 4 July 2011. Retrieved 24 November 2010.
  2. ^ "TV Technology PAL". Publication date unknown. Thinkbox. Archived from the original on 5 December 2010. Retrieved 24 November 2010.
  3. ^ "Color Television History". Publication date unknown. About.com. Retrieved 24 November 2010.
  4. ^ "Color subcarrier frequency and TV Standards/TV Systems". Publication dates 2002, 2003, 2004, 2005 last updated 2005/12/15. Paradiso Design. Retrieved 24 November 2010.
  5. ^ "Pal systems – Television measurements" (PDF). Publication date September 1999. Tektronics Incorporated. Archived from the original (PDF) on 18 July 2011. Retrieved 25 November 2010.
  6. ^ a b c Gupta, R. G. (2006). Television Engineering and Video Systems. Tata McGraw-Hill. p. 62. ISBN 0-07-058596-2.
  7. ^ a b c Pemberton, Alan (30 November 2008). "World Analogue Television Standards and Waveforms". Pembers' Ponderings. Sheffield, England. Archived from the original on 20 February 2008. Retrieved 25 September 2010.
  8. ^ Wharton, W.; Douglas Howorth (1971). Principles of Television Reception (illustrated ed.). Pitman Publishing. ISBN 0-273-36103-1. OCLC 16244216.
  9. ^ Mills, Thomas. "A five function IC for television receivers". ResearchGate. IEEE. Retrieved 11 May 2019.
  10. ^ "TACKLING THE POWER SUPPLY". Publication date – unknown. Old Tellys.co.uk. Archived from the original on 3 March 2012. Retrieved 24 November 2010.
  11. ^ "An Investigation Into the EMC Emissions From Switched Mode Power Supplies and Similar Switched Electronic Load Contollers Operating at Various Loading Conditions – Page 2,line 3" (PDF). Publication date – January 2001. York EMC.co.uk. Archived (PDF) from the original on 15 March 2012. Retrieved 24 November 2010.
  12. ^ "Review of Primary Frequency Control Requirements on the GB Power System Against a Background of Increase in Renewable Generation – Impact of railway electrification systems on other electrical systems and civil infrastructures within and outside the railway environment.-section 3.2,page 15" (PDF). October 2006. Bura.Brunel.ac.uk. Archived (PDF) from the original on 15 March 2012. Retrieved 24 November 2010.
  13. ^ "Technical note 77 – Diode Split for E.H.T. generation" (PDF). Publication date – 1976. Mullard. Archived (PDF) from the original on 21 July 2011. Retrieved 24 November 2010.
  14. ^ Stephanie Condon (26 January 2009). "Senate OKs delay of digital television transition". CNET News. Archived from the original on 25 October 2012. Retrieved 14 June 2009.
  15. ^ "Archived copy". Archived from the original on 11 April 2009. Retrieved 5 May 2009.CS1 maint: Archived copy as title (link)
  16. ^ Countdown | RTRS
  17. ^ [http://www.nat.ru/ Plan to switch off analog television in Russia, approved by the decision of the Government Commission for the development of broadcasting on November 29, 2018 | The National Association Of Broadcasters

External links

Analog passthrough

Analog passthrough is a feature found on some digital-to-analog television converter boxes. Boxes without analog passthrough only allow digital TV (ATSC standard) to be viewed on older, analog-only (NTSC standard) TVs. Those with analog passthrough allow both digital and analog television to be viewed on older TVs.

Before digital television, passthrough originally existed for VCRs (and later PVRs and DVDRs), allowing the TV antenna or cable TV signal to pass through the VCR (with a slight insertion loss) to the TV set automatically when the VCR was turned off, or manually with a button on the remote control. Passthrough was turned off when the RF modulator (typically on TV channel 3 or 4 in North America) was on, as this F connector was originally the only way to send the VCR output to older TVs, until unmodulated composite video and RCA connectors became common.

Broadcast television systems

Terrestrial television systems (or Broadcast television systems in the US and Canada) are the encoding or formatting standards for the transmission and reception of terrestrial television signals. There were three main analog television systems in use around the world until the late 2010s (expected): NTSC, PAL, and SECAM. Now in digital terrestrial television (DTT), there are four main systems in use around the world: ATSC, DVB, ISDB and DTMB.

Cable television

Cable television is a system of delivering television programming to consumers via radio frequency (RF) signals transmitted through coaxial cables, or in more recent systems, light pulses through fiber-optic cables. This contrasts with broadcast television (also known as terrestrial television), in which the television signal is transmitted over the air by radio waves and received by a television antenna attached to the television; or satellite television, in which the television signal is transmitted by a communications satellite orbiting the Earth and received by a satellite dish on the roof. FM radio programming, high-speed Internet, telephone services, and similar non-television services may also be provided through these cables. Analog television was standard in the 20th century, but since the 2000s, cable systems have been upgraded to digital cable operation.

A "cable channel" (sometimes known as a "cable network") is a television network available via cable television. When available through satellite television, including direct broadcast satellite providers such as DirecTV, Dish Network and Sky, as well as via IPTV providers such as Verizon FIOS and AT&T U-verse is referred to as a "satellite channel". Alternative terms include "non-broadcast channel" or "programming service", the latter being mainly used in legal contexts. Examples of cable/satellite channels/cable networks available in many countries are HBO, Cinemax, MTV, Cartoon Network, AXN, E!, FX, Discovery Channel, Canal+, Eurosport, Fox Sports, Disney Channel, Nickelodeon, CNN International, and ESPN.

The abbreviation CATV is often used for cable television. It originally stood for Community Access Television or Community Antenna Television, from cable television's origins in 1948. In areas where over-the-air TV reception was limited by distance from transmitters or mountainous terrain, large "community antennas" were constructed, and cable was run from them to individual homes. The origins of cable broadcasting for radio are even older as radio programming was distributed by cable in some European cities as far back as 1924.

Chilevisión

Chilevisión (CHV) is a Chilean free-to-air television channel. Is the third oldest Chilean television network, and was formerly called Canal 9 de Televisión de la Universidad de Chile, Teleonce (Universidad de Chile Televisión) and RTU (Red de Televisión de la Universidad de Chile), this TV station was owned by Universidad de Chile, a Chilean state university. This educational institution sold a significant percentage of its TV channel to Venevisión, changing its name to Chilevisión. It was later sold to Claxson Interactive Group and then to Chilean investor and president Sebastián Piñera.

On 28 August 2010, it was announced that Turner Broadcasting System Latin America had reached an agreement to purchase it. This assets do not include the analog television channel frequency which is still owned by Universidad de Chile and is used under a paid usufruct scheme, similar to a lease. This contract expires in 2018 and only affects the analog frequencies used by the station. On 6 October 2010 the purchase was materialized.

Digital Transition and Public Safety Act of 2005

The Digital Television Transition and Public Safety Act of 2005 is a United States Congress legislation enacted on October 20, 2005. This act deals with the cessation of the broadcasting of analog television and the subsequent implementation of digital television. This transition took place on June 12, 2009, which had been scheduled for February 17, 2009.

Digital television

Digital television (DTV) is the transmission of television signals, including the sound channel, using digital encoding, in contrast to the earlier television technology, analog television, in which the video and audio are carried by analog signals. It is an innovative advance that represents the first significant evolution in television technology since color television in the 1950s. Digital TV transmits in a new image format called high definition television (HDTV), with greater resolution than analog TV, in a wide screen aspect ratio similar to recent movies in contrast to the narrower screen of analog TV. It makes more economical use of scarce radio spectrum space; it can transmit multiple channels, up to 7, in the same bandwidth occupied by a single channel of analog television, and provides many new features that analog television cannot. A transition from analog to digital broadcasting began around 2006. Different digital television broadcasting standards have been adopted in different parts of the world; below are the more widely used standards:

Digital Video Broadcasting (DVB) uses coded orthogonal frequency-division multiplexing (OFDM) modulation and supports hierarchical transmission. This standard has been adopted in Europe, Africa, Asia, Australia, total about 60 countries.

Advanced Television System Committee (ATSC) uses eight-level vestigial sideband (8VSB) for terrestrial broadcasting. This standard has been adopted by 6 countries: United States, Canada, Mexico, South Korea, Dominican Republic and Honduras.

Integrated Services Digital Broadcasting (ISDB) is a system designed to provide good reception to fixed receivers and also portable or mobile receivers. It utilizes OFDM and two-dimensional interleaving. It supports hierarchical transmission of up to three layers and uses MPEG-2 video and Advanced Audio Coding. This standard has been adopted in Japan and the Philippines. ISDB-T International is an adaptation of this standard using H.264/MPEG-4 AVC that been adopted in most of South America and is also being embraced by Portuguese-speaking African countries.

Digital Terrestrial Multimedia Broadcasting (DTMB) adopts time-domain synchronous (TDS) OFDM technology with a pseudo-random signal frame to serve as the guard interval (GI) of the OFDM block and the training symbol. The DTMB standard has been adopted in the People's Republic of China, including Hong Kong and Macau.

Digital Multimedia Broadcasting (DMB) is a digital radio transmission technology developed in South Korea as part of the national IT project for sending multimedia such as TV, radio and datacasting to mobile devices such as mobile phones, laptops and GPS navigation systems.

Digital television in the United States

See digital television for more technical details, or DTV transition in the United States for specific information related to the analog-to-digital switchoverIn the United States, digital television broadcasts, or DTV, can be received via cable, via internet, via satellite, or via digital terrestrial television - much like analog television broadcasts have been. Full-power analog television broadcasts, however, were required by U.S. federal law to cease by June 12, 2009. Low-power, Class A, and TV Translator stations are not currently required to cease analog broadcasts. Also by law, digital broadcasts - when transmitted as OTA signals - must conform to ATSC standards.; it is unclear whether satellite operators are free to use their own proprietary standards; and many standards exist for Internet television (most are proprietary).

Digital television transition

The digital television transition, also called the digital switchover, the analog switch-off (ASO), or the analog shutdown, is the process, mainly begun in 2006 (for terrestrial broadcasting), in which older analog television broadcasting technology is converted to and replaced by digital television. Conducted by individual nations on different schedules, this primarily involves the conversion of analog terrestrial television broadcasting infrastructure to digital terrestrial. However, it also involves analog cable conversion to digital cable or internet protocol television, as well as analog to digital satellite television. Transition of land based broadcasting was begun by some countries around 2000. By contrast, transition of satellite television systems was well underway or completed in many counties by this time. It is an involved process because the existing analog television receivers owned by viewers cannot receive digital broadcasts; viewers must either purchase new digital TVs, or converter boxes which change the digital signal to an analog signal or some other form of a digital signal (i.e. HDMI) which can be received on the older TV.

In many countries, a simulcast service is operated where a broadcast is made available to viewers in both analog and digital at the same time. As digital becomes more popular, it is expected that the existing analog services will be removed. In most places this has already happened, where a broadcaster has offered incentives to viewers to encourage them to switch to digital. In other cases government policies have been introduced to encourage or force the switchover process, especially with regard to terrestrial broadcasts. Government intervention usually involves providing some funding for broadcasters and, in some cases, monetary relief to viewers, to enable a switchover to happen by a given deadline. Governments can also require all receiving equipment sold in a country to support the necessary digital reception 'tuner'.

The switchover process is being accomplished on different schedules in different countries; in some countries it is being implemented in stages as in Australia, Brazil, India, Mexico, and the United Kingdom, where each region has a separate date to switch off. In others, the whole country switches on one date, such as the Netherlands, which switched off its analog terrestrial services on 11 December 2006. On 3 August 2003, Berlin became the world's first city to switch off terrestrial analog signals. Luxembourg was the first country to complete its terrestrial switchover, in September 2006.

Flash cut

A flash cut, also called a flash cutover, is an immediate change in a complex system, with no phase-in period.

In the United States, some telephone area codes were split or overlaid immediately, rather than being phased in with a permissive dialing period. An example is telephone area code 213, which serves downtown Los Angeles and its immediate environs, split in January 1951 into 213 and 714 all at once. Another example is an immediate switch from an analog television channel to a digital television channel on the same frequency, where the two cannot operate in parallel without interference.

A flash cut can also define a procedure in which multiple components of computer infrastructure are upgraded in multiple ways, all at once, with no phase-in period.

High frame rate

In motion picture technology—either film or video—high frame rate (HFR) refers to higher frame rates than typical prior practice.

The frame rate for motion picture film cameras was typically 24 frames per second (fps) with multiple flashes on each frame during projection to prevent flicker. Analog television and video employed interlacing where only half of the image (known as a video field) was recorded and played back/refreshed at once but at twice the rate of what would be allowed for progressive video of the same bandwidth, resulting in smoother playback, as opposed to progressive video which is more similar to how celluloid works. The field rate of analog television and video systems was typically 50 or 60 fields per second. Usage of frame rates higher than 24 FPS for feature motion pictures and higher than 30 FPS for other applications are emerging trends in the recent past.

KBKF-LP

KBKF-LP is a low-power analog television station in San Jose, California, broadcasting to the South Bay region of the San Francisco Bay Area on VHF channel 6 from Loma Prieta Peak. The station is owned by Venture Technologies Group, LLC.

Operating as an FM radio station, KBKF-LP utilizes the 87.75 MHz audio carrier to broadcast Contemporary Christian music from the K-LOVE radio network. As a result, the station's audio signal can be received on most FM radio receivers.

List of analog television stations in the Philippines

This is a list of analog television stations in the Philippines. Currently, there are three major networks competing for bigger audience share; ABS-CBN Corporation, GMA Network Inc. and TV5 Network Inc. Major free-to-air networks are popularly known by their flagship channels (example GMA 7 (Manila) instead of simply GMA Network). Analog television in the Philippines began to shut down on February 28, 2017, and is scheduled to complete by 2023. Currently, all analog TV stations are still using the NTSC standard.

Second audio program

Second audio program (SAP), also known as secondary audio programming, is an auxiliary audio channel for analog television that can be broadcast or transmitted both over-the-air and by cable television. SAP is part of the multichannel television sound (MTS) standard originally set by the National Television Systems Committee (NTSC) in 1984 in the United States. The NTSC video format and MTS are also used in Canada and Mexico.

Split sound system

Split sound is an old system in analog television transmitters. It has long been superseded, but transmitters working on this principle are still in use. In this system there are two almost independent transmitters, one for sound (aural) and one for picture (visual). The system requires more energy input relative to broadcast energy than the alternative system known as intercarrier system.

TV Kumanovo

TV Kumanovo (Macedonian Cyrillic: ТВ Куманово) was a local terrestrial analog television channel in Kumanovo, North Macedonia.

Television transmitter

A television transmitter is a transmitter that is used for terrestrial (over-the-air) television broadcasting. It is an electronic device that radiates radio waves that carry a video signal representing moving images, along with a synchronized audio channel, which is received by television receivers ('televisions' or 'TVs') belonging to a public audience, which display the image on a screen. A television transmitter, together with the broadcast studio which originates the content, is called a television station. Television transmitters must be licensed by governments, and are restricted to a certain frequency channel and power level. They transmit on frequency channels in the VHF and UHF bands.

Television transmitters use one of two different technologies: analog, in which the picture and sound are transmitted by analog signals modulated onto the radio carrier wave, and digital in which the picture and sound are transmitted by digital signals. The original television technology, analog television, began to be replaced in a transition beginning in 2006 in many countries with digital television (DTV) systems. These transmit pictures in a new format called HDTV (high definition television) which has higher resolution and a wider screen aspect ratio than analog. DTV makes more efficient use of scarce radio spectrum bandwidth, as several DTV channels can be transmitted in the same bandwidth as a single analog channel. In both analog and digital television, different countries use several incompatible modulation standards to add the video and audio signals to the radio carrier wave,

The principles of primarily analog systems are summarized as they are typically more complex than digital transmitters due to the multiplexing of VSB and FM modulation stages.

Vertical blanking interval

In a raster graphics display, the vertical blanking interval (VBI), also known as the vertical interval or VBLANK, is the time between the end of the final line of a frame or field and the beginning of the first line of the next frame. It is present in analog television, VGA, DVI and other signals. During the VBI, the incoming data stream is not displayed on the screen. In raster cathode ray tube displays, the beam is blanked to avoid displaying the retrace line; see raster scan for details. The signal source, such as a television broadcast, does not supply image information during the blanking period.

The VBI was originally needed because of the inductive inertia of the magnetic coils which deflect the electron beam vertically in a CRT; the magnetic field, and hence the position being drawn, cannot change instantly. Additionally, the speed of older circuits was limited. For horizontal deflection, there is also a pause between successive lines, to allow the beam to return from right to left, called the horizontal retrace or horizontal blanking interval. Modern CRT circuitry does not require such a long blanking interval, and thin panel displays require none, but the standards were established when the delay was needed (and to allow the continued use of older equipment). Blanking of a CRT may not be perfect due to equipment faults or brightness set very high; in this case a white retrace line shows on the screen, from bottom right to top left.

In analog television systems the vertical blanking interval can be used for datacasting (to carry digital data), since nothing sent during the VBI is displayed on the screen; various test signals, time codes, closed captioning, teletext, CGMS-A copy-protection indicators, and various data encoded by the XDS protocol (e.g., the content ratings for V-chip use) and other digital data can be sent during this time period. In U.S. analog broadcast television, line 19 was reserved for a Ghost-canceling reference line 21 was reserved for captioning data. The obsolete Teletext service contemplated the use of line 22 for data transmission.

The pause between sending video data is used in real time computer graphics to perform various operations on the back buffer before copying it to the front buffer instead of just switching both pointers, or to provide a time reference for when switching such pointers is safe.

In video game systems the vertical blanking pulses are extensively used to time the plotting of new graphics/removal of old ones in order to avoid screen tearing, as they occur at an accurately known frequency, and many systems up to the 16-bit era featured games and other graphical programs where drawing was conducted during the blanking interval for this reason. Cases where synchronising game code this way was more necessary than preferable and made early video game systems such as the Atari 2600 difficult to program.

Special raster techniques on the Atari 2600, Nintendo Entertainment System, and other consoles allowed extending this interval at the cost of some blank scanlines at the top or bottom of the screen, which may or may not end up in the overscan area. The use of double buffering in modern graphics hardware has rendered these techniques obsolete.

Most consumer VCRs use the known black level of the vertical blanking pulse to set their recording levels. The Macrovision copy protection scheme inserts pulses in the VBI, where the recorder expects a constant level, to disrupt recording to videotapes.

Video

Video is an electronic medium for the recording, copying, playback, broadcasting, and display of moving visual media. Video was first developed for mechanical television systems, which were quickly replaced by cathode ray tube (CRT) systems which were later replaced by flat panel displays of several types.

Video systems vary in display resolution, aspect ratio, refresh rate, color capabilities and other qualities. Analog and digital variants exist and can be carried on a variety of media, including radio broadcast, magnetic tape, optical discs, computer files, and network streaming.

Zweikanalton

Zweikanalton ("two-channel sound") or A2 Stereo, is an analog television sound transmission system used in Germany, Austria, Australia, Switzerland, Netherlands and other countries that use or used PAL-B or PAL-G. South Korea formerly utilised its variant of this format in analogue television system until 31 December 2012. It relies on two separate FM carriers.

This offers a relatively high separation between the channels (compared to a subcarrier-based multiplexing system) and can thus be used for bilingual broadcasts as well as stereo. Unlike the competing NICAM standard, Zweikanalton is an analog system.

Medium
Broadcasting
niche
Specialty
channels
Production
and funding
History
Pioneers
Transmission
media
Network topology
and switching
Multiplexing
Networks

This page is based on a Wikipedia article written by authors (here).
Text is available under the CC BY-SA 3.0 license; additional terms may apply.
Images, videos and audio are available under their respective licenses.